• 

  Christine Leong

  • 4 months ago
  • Data converters
  • Data converters forum

  ADC-WB-BB: Request for 3D/CAD Model

  TI Thinks Resolved

  Part Number: ADC-WB-BB Hi TI, Does the ADC-WB-BB board have any 3D/CAD model in STEP/IGES format? I need to design it into my chassis along with other stuff.
• 

  usethewrench

  • 8 months ago
  • Data converters
  • Data converters forum

  ADC-WB-BB: ADC-WB-BB or similar

  TI Thinks Resolved

  Part Number: ADC-WB-BB The containerized ADC-WB-BB is a convenient packaging of the Minicircuit balun it uses. I am wondering if you offer a similarly packaged product, but using Mini Circuits or other baluns that extend down to .2 or .4 MHz. Thanks...
• 

  jim s

  • over 1 year ago
  • Data converters
  • Data converters forum

  RE: ADC-WB-BB: Application Compatability

  Yes, since this is a 2:1 transformer.
• 

  Shawn Han

  • over 2 years ago
  • Clock & timing
  • Clock & timing forum

  RE: Phase jitter measurement methodology question

  Hi Rob, Refer to www.ti.com/.../adc-wb-bb Before using balun, it is also fine to measure with single end with another port 50 Ohm terminated. Regards, Shawn
• 

  usethewrench

  • 8 months ago
  • Clock & timing
  • Clock & timing forum

  RE: LMK04828: LMK04832/LMK04828 driving LMK04828 single ended reference input

  Hello Derek, Hopefully my re uploaded diagram works. I was hoping that you would be able to respond, I just didn't want to come across as demanding or dictating who should respond, if perhaps you and another of your colleagues shared the load...
• 

  jim s

  • over 1 year ago
  • Data converters
  • Data converters forum

  RE: TSW40RF82EVM: Schematic of TSW40RF82EVM

  Channamallesh, Yes, you can use those SMA's to bring in an analog input. You will have to move two resistors to allow this. You can use a transformer board made by TI called the "ADC-WB-BB" that has a transformer with a bandwidth from...
• 

  Ali Sorouri

  • over 3 years ago
  • Data converters
  • Data converters forum

  ADC-WB-BB: application

  • Resolved

  Part Number: ADC - WB - BB Hi, I have purchased two of these converters to measure the insertion loss
• 

  Timothy T

  • over 1 year ago
  • Clock & timing
  • Clock & timing forum

  RE: LMK04828: Balun for converting differential output to single ended

  What is the output frequency? Here are some suggestions: ADT2-1T is one option. ADT2-1T-1P is another for higher frequency. For higher frequency consider the TC1-1-13MA+ as in ( ) - note it is a 1:1 balun, so see note about impedance matching on liinked...
• 

  Ron Breding

  • over 1 year ago
  • Clock & timing
  • Clock & timing forum

  LMK04828BEVM: LMK04828BEVM DCLK0 output levels to drive DAC3484EVM CLKIN on J9 (i.e. to the CDCE62005 External Clock input)

  • Resolved

  * and connected to a ADC - WB - BB balun that connects to the J9 CLKIN input of the DAC3484EVM. The signal gets
• 

  Lane Boyd

  • over 2 years ago
  • Clock & timing
  • Clock & timing forum

  RE: LMK04828BEVM: What BALUN modules would you suggest going from the 240 Ohm outputs to 50 terminations?

  Hi Ron, Here are some baluns I can recommend that I commonly use: Macom H-183-4 Wavecrest 530900 TI ADC-WB-BB Kind regards, Lane

Didn't find what you are looking for? Post a new question.

• Ask a new question