Search tips
Showing 57 results View by: Thread Post Sort by

  • ADC16DV160: ADC and DAC selection for 4-20mA Analog Input and Outputs

    TI Thinks Resolved
    Part Number: ADC16DV160 Other Parts Discussed in Thread: AMC3301 , ADC3444 Dear Ti Team, Im new to the design of ADC and DAC for 4-20mA analog Input and output industrial applications.I have attahced the complete design requirement. Could you please have…

  • ADC16DV160: SPI：ESD protection diode

    TI Thinks Resolved
    Part Number: ADC16DV160 Hi, Is the ESD protection diode of the SPI input terminal connected to the VA3.0 power supply? According to the absolute maximum rating Note 5), it is VA3.0, but considering the power supply voltage of SPI, it looks like VDR（ Nominal…

  • ADC16DV160: Clock input issue

    TI Thinks Resolved
    Part Number: ADC16DV160 Hi , Looking into your EVB schematic you put an ATD1-1WT+ transformer with 75 Ohm impedance on clock inputs port , is there a reason why you took this and not standard 50 Ohm ? A fast response will be appreciate without measure…

  • ADC16DV160: LVDS Output Operating Supply

    TI Thinks Resolved
    Part Number: ADC16DV160 Hi, In ADC16DV160 Part, The output LVDS Data Lines DO+I/DO-I & DO+Q/DO-Q are Operating based on which specific power supply? VA3.0 or VA1.8 or VDR ? Thanks in Advance, Devaguru V

  • RE: ADC16DV160: Input Impedance Value & Sim

    HI, The Situation is , i am in desperate need to verify my input Circuit to ADC16DV160 to proceed along with building my circuit physically. Can you kindly generate and Provide S1P file @ 900-1200MHz or Please state is there any other Virtual way to verify…

  • ADC16DV160: FPGA communication problems

    Part Number: ADC16DV160 Hello I have a problem with the ADC16DV160 which is built on an FPGA board with an Artix 7. The power supply is designed according to the specifications in the data sheet. The clock is generated directly by the FPGA and is dc coupled…
    • Answered

  • LMH5401: Output circuitry to match ADC16DV160

    Resolved
    Part Number: LMH5401 Other Parts Discussed in Thread: ADC16DV160 Hi ! I am trying to use LMH5401 to convert single ended input to differential , amplify and then feed to ADC16DV160 Input channels as per the requirements below, Fundamental I/P Frequency…
    • Resolved

  • RE: Requirement on ADC and DAC

    Hello, I believe this may be a duplicate post - please refer here: https://e2e.ti.com/support/data-converters-group/data-converters/f/data-converters-forum/1269030/adc16dv160-adc-and-dac-selection-for-4-20ma-analog-input-and-outputs Regards, Amy

  • ADC16DV160: Request for IBIS model of ADC16DV160CILQE/NOPB

    Part Number: ADC16DV160 Hi, The IBIS model of ADC16DV160CILQE/NOPB is not available in TI website. Can I get the IBIS model for carrying out signal integrity analysis of my card. thanks V.Deva kumar HAL Email: v.devakumar@hal-india.co.in vijayakanth.b…

  • ADC16DV160: Why common mode 1.15V is almost the same as reference voltage 1.2?

    Part Number: ADC16DV160 Other Parts Discussed in Thread: LMH6554 , Hello! We are driving ADC with amplifier LMH6554 with +-2.5V supply. We set common mode to input signal with ADC VRM output which is about 1.15V. As we usually have weak signals, we do not…

Didn't find what you are looking for? Post a new question.