Search tips
Showing 27 results View by: Thread Post Sort by

  • ADC3441: HDL Interface for ADC3441 (Serial LVDS) with FPGA

    Part Number: ADC3441 Tool/software: Hello TI Team, I am currently working on interfacing the ADC3441 with an FPGA (Xilinx/Altera) using a Serial LVDS interface. I wanted to check if you provide any HDL (Verilog/VHDL) reference design, example code,…
    • Answered

  • ADC3441: output data rate on LVDS

    Resolved
    Part Number: ADC3441 Other Parts Discussed in Thread: ADC3442 Hi May I have question about ADC344x? My customer is considering ADC3441 for RX in mmWave rader sensor. Question 1 : I think ADC344x have max sampling rate in each device. Could we use another…
    • Resolved
    • Answered

  • ADC3441: accuracy comparsion

    Resolved
    Part Number: ADC3441 Other Parts Discussed in Thread: ADC3421 if look at below ENOB, it means there is quite small difference using ADC3421 and ADC3441. Is it right?
    • Resolved

  • ADC3441: Synchronization issues

    TI Thinks Resolved
    Part Number: ADC3441 Are the sampling of the 4 channels synchronized? From this timing chart, does the output data appear to be out of sync? Latency=8 x CLKIN Cycles+tPDI - tA, what does this delay time refer to?
    • Answered

  • ADC3441: What is the minimum sampling rate of ADC3441?

    Resolved
    Part Number: ADC3441 Hello guys, One of my customers is considering using ADC3441 for their new products. They have the following questions at this moment. Could you please give me your reply for them? Q1. What is the minimum sampling rate of ADC3441?…
    • Resolved

  • ADC3441: Interfacing with 7 series Xilinx FPGA

    TI Thinks Resolved
    Part Number: ADC3441 Hi, My team is interfacing with the AD3441 and we have built a digital board that houses Xilinx Artix-7 FPGA. I was wondering is there some IP available that can connect to ADC3441 or a similar ADC that also supports AXI-S protocol…
    • Answered

  • ADC3441: How to understand "Each input pin (INP, INM) must swing symmetrically between (VCM + 0.5 V) and (VCM – 0.5 V)" in datasheet of ADC3444

    Resolved
    Part Number: ADC3441 Other Parts Discussed in Thread: ADC3444 , ADC3444EVM , LMH5401 I want to use ADC3444 to digitalize a wide bandwidth analog signal with single polarity from -0.2V~1V. As described in datasheet that "Each input pin (INP, INM) must swing…
    • Resolved
    • Answered

  • ADC3441: Setup and hold times for 20 MSPS (2 wire mode)

    Resolved
    Part Number: ADC3441 Hi, In the datasheet for the device it lists in Table 1 setup and hold times for a selection of sampling frequencies (for 2 wire mode), but this does not include values for 20 MSPS. Do I need to use the values listed for 25 MSPS,…
    • Resolved
    • Answered

  • ADC3441: ADC3441 ECCN

    Resolved
    Part Number: ADC3441 Hi, I am electronic designer and we whant use your products. For the your project (new Motor Servodrive ), that we're developing we use the ADC3441IRTQT (quad ADC 14bit) and OMAPL138EZWT4 (ARM-DSP) I needed to know if some of…
    • Resolved
    • Answered

  • ADC3441: Input clock jitter tradeoffs

    Resolved
    Part Number: ADC3441 Dear forum members. Could you please comment on the following? Background: We intend to use a ADS3441 in a new application at 25 MSPS. The clock will be LVDS at 10MHz (CLKP-CLKM), frequency could be changed if needs be. Question: If…
    • Resolved

Didn't find what you are looking for? Post a new question.