Search tips
Showing 12 results View by: Thread Post Sort by

  • RE: ADC34RF52: How to fix the NCO initial phase

    Hi, Yes, write these at the end of the device configuration to mask the SYSREF function only to the NCO phase reset. Then enable the internal SYSREF input and clear the SYSREF counter and start the SYSREF counter again. After one SYSREF edge, the NCO…
    • Answered

  • ADC34RF52: CAL_STATUS Register

    Resolved
    Part Number: ADC34RF52 Other Parts Discussed in Thread: ADC32RF55 Tool/software: Hi team, My customer is evaluating the board with the ADC34RF52, but the calibration has not been completed correctly and the analogue-to-digital conversion data is not…
    • Resolved
    • Answered

  • ADC34RF52: How to Determine Grayed Registers

    Resolved
    Part Number: ADC34RF52 Tool/software: Hi team, In the ADC34RF52 datasheet 8.3.1, the initial configuration example is shown. But some of fields are grayed which are not documented in the register summary table. Could you provide the document with all…
    • Resolved
    • Answered

  • ADC34RF52: Difference between ADC34RF52 and ADC34RF55

    Resolved
    Part Number: ADC34RF52 Other Parts Discussed in Thread: ADC34RF55 , Hi team, Could you let me know the difference between ADC34RF52 and ADC34RF55? I know the sampling rate difference (1.5Gsps and 3Gsps). What else? Best regards, Kazuki Itoh
    • Resolved
    • Answered

  • ADC34RF52: ADC34RF52IRTD package size and tolerance

    Resolved
    Part Number: ADC34RF52 My customer wants to know ADC34RF52IRTD package size and toleance. Could you please let me know below value ? a. Tolerance of side pin (0.2 ± xx mm ?) b. Max value of stand off. If it is not defined, actual value is also…
    • Resolved
    • Answered

  • ADC34RF52: FIR filter details

    Resolved
    Part Number: ADC34RF52 In the data sheet 7.3.5(ADC34RF52) it is stated that the output of the decimation filters are 16-bit resolution. How many bits are used between the filters and how are bits removed, dropped, rounded, truncated or saturated?
    • Resolved
    • Answered

  • ADC34RF52: Unused input termination

    Resolved
    Part Number: ADC34RF52 Other Parts Discussed in Thread: LMK04832 Hi team, Could you let me know how to terminate the unused input channels of ADC34RF52? Best regards, Kazuki Itoh
    • Resolved
    • Answered

  • ADC34RF52: Minimum input differential voltage

    Resolved
    Part Number: ADC34RF52 Hi team, Could you please let me know the clock input (CLKP/M) minimum input differential voltage V_ID of ADC34RF52? The max. and typ. values are specified in the datasheet, but the minimum value is not specified. Best regards, …
    • Resolved
    • Answered

  • ADC34RF52: JESD204B LaneRate

    Resolved
    Part Number: ADC34RF52 I am trying to calculate Lanerate when using ADC34RF52. - L: number of lanes per link - M: number of converters per device - F: number of octets per frame clock period - S: number of samples per frame -Fs: sampling clock The formula…
    • Resolved
    • Answered

  • ADC34RF52: Input Clock Specifications

    Resolved
    Part Number: ADC34RF52 Hello, Would you clarify TI's definition of VID (differential input voltage) for the ADC34RF52 Clock input. The spec indicated Is VID measured from signal itself as VOD seen below: or is it measured as what is seen by the…
    • Resolved

Didn't find what you are looking for? Post a new question.