Search tips
Showing 41 results View by: Thread Post Sort by

  • ADS1114: I2C output

    • Resolved
    Part Number: ADS1114 Hello experts, I got question about I2C output from customer. 1. ADS1114 's I2C

  • ADS1114: Set to assert conversion ready pulse after every 2 conversions, but asserts every single conversion

    • Resolved
    Part Number: ADS1114 Hi, I'm having trouble figuring out why I can't get the ADS1114 to generate

  • Looking for a ADC

    Hi I am looking for a ADC. But can not find a suitable one. Would you please help? Detail case as below: - Signal to measure, micro current. - Range: 1.13uA to 1.43uA - Resolution: 72nA - SPI interface - With Digital Comparator inside -...

  • Compiler/ADS1114: ADS1114

    • Resolved
    Part Number: ADS1114 Tool/software: TI C/C++ Compiler Dear Sir, Could you please let me know how

  • RE: Compiler/ADS1114: ADS 1114 conversion results

    Thank you. I'll look in that direction.

  • ADS1114：Low side bidirectional current sensing

    TI Thinks Resolved
    Part Number: ADS1114 Low-side bidirectional current sensing requires a first-order operational amplifier，If the PGA is sufficient，Is it possible not to add a front-end operational amplifier? But bi-directional current may cause pin voltage to be lower...

  • RE: ADS1114: SFOCAL calibration command (0x19) does not update OFCAL registers

    Hi Bob, Sorry for the delay in replying, I didn't get an email for your response above. Rref is 0.1% tolerance resistor. I simulate the Rrtd using a 1K potentiometer. I take your point regarding the voltage measurement. I'll measure resistance...

  • ADS1114: I2C interface to coexist with PMBUS

    TI Thinks Resolved
    Part Number: ADS1114 Hi Experts, Can ADS1114IDGST coexist with standard PMBUS device on the same I2C interface? Any potential risk? Thanks

  • ADS1114: Double buffer of converion register

    • Resolved
    Part Number: ADS1114 Should the reading of the conversion register be synchronized

  • RE: TLA2022: ADC TLA2022 Single ended input

    Matias, The TLA2022 will have only 1 single ended input. If you look at the configuration register, this is basically set as if the input multiplexer configuration (MUX[2:0]) is only set to 000. Looking at the Config Register Field Descriptions table...

Didn't find what you are looking for? Post a new question.


All content and materials on this site are provided "as is". TI and its respective suppliers and providers of content make no representations about the suitability of these materials for any purpose and disclaim all warranties and conditions with regard to these materials, including but not limited to all implied warranties and conditions of merchantability, fitness for a particular purpose, title and non-infringement of any third party intellectual property right. No license, either express or implied, by estoppel or otherwise, is granted by TI. Use of the information on this site may require a license from a third party, or a license from TI.

Content on this site may contain or be subject to specific guidelines or limitations on use. All postings and use of the content on this site are subject to the Terms of use of the site; third parties using this content agree to abide by any limitations or guidelines and to comply with the Terms of use of this site. TI, its suppliers and providers of content reserve the right to make corrections, deletions, modifications, enhancements, improvements and other changes to the content and materials, its products, programs and services at any time or to move or discontinue any content, products, programs, or services without notice.

TI worldwide | Contact us | myTI login | Corporate citizenship

TI is a global semiconductor design and manufacturing company. Innovate with 100,000+ analog ICs and
embedded processors, along with software, tools and the industry’s largest sales/support staff.

© Copyright 1995-2020 Texas Instruments Incorporated. All rights reserved.
Trademarks | Privacy policy | Terms of use