Search tips
Showing 207 results View by: Thread Post Sort by

  • ADS124S06: Error in the voltage measurement at high sampling rate

    TI Thinks Resolved
    Part Number: ADS124S06 Hello, We are using ADS124S06 for measuring the voltage values. The hardware design is same as the development board. The input mode is differential and the DATARATE is 4000SPS, rest of the registers are set to the default. We are…
    • Answered

  • ADS124S06: ADS124S06: Frist ADC Data output is not correct for Multi slave SPI connections, Other two ADCs data output is correct in Same SPI.

    Resolved
    Part Number: ADS124S06 Other Parts Discussed in Thread: TMS570LS3137 , , ADS124S08 Dear TI team, We are using ADS124S06 device for one of the differential measurement, I have connected three ADCs in single SPI of TMS570LS3137. Below image refers my Digital…
    • Resolved
    • Answered

  • ADS124S06: ADC Data conversion (initial) time

    Resolved
    Part Number: ADS124S06 We are using ADS124s06 ADC. Measurement is in continuous mode with the data rate of 4000SPS and we are using the low-latency filter. As per our understanding from the datasheet, reading data from one channel is possible at a time…
    • Resolved
    • Answered

  • ADS124S06: R value in VBIAS circuit

    Resolved
    Part Number: ADS124S06 Hello, The below is VBIAS generator block diagram from the datasheet. They would like to know the value of one R in the voltage divider ? Could you tell me the value? If possible, could you also possible to tell me MIN/MAX value…
    • Resolved

  • ADS124S06: VBAISの分割抵抗について

    TI Thinks Resolved
    Part Number: ADS124S06 9.3.8 Bias Voltage Generation 図76. VBAIS Block Diagramについて分割抵抗がR, 5R, 6R と記述されています。 R 1つの定数の数値をご教示願います。可能であれば、R の許容差および温度特性も含めてご教示頂けると幸いです。 2023/7/14 まで一報いただけると幸いです。 以上、お手数おかけしますがよろしくお願い致します。
    • Answered

  • ADS124S06: Acquisition Problem

    Resolved
    Part Number: ADS124S06 Hello, Sorry for this silly question, but I have to admit that I can't figure it out. I use a sensor powered by 3V3 which has two analog outputs. These outputs have a reference which equals VDD/2 with respect to ground. I will…
    • Resolved

  • ADS124S06: ADC Channel Over-reading

    TI Thinks Resolved
    Part Number: ADS124S06 Other Parts Discussed in Thread: ADS124S08 Hi I have seen this problem with similar circuits using both the ADS124S06 and ADS124S08. I am using the device with a single 3v3 supply. I believe the supply is OK and I have the recommended…
    • Answered

  • ADS124S08: Is it possible to use ADS124S08 instead of ADS124S06 with same software

    Resolved
    Part Number: ADS124S08 Other Parts Discussed in Thread: ADS124S06 , , ADS114S06 , ADS114S08 Dear Specialists, My customer is considering ADS124S08 as substitute for ADS124S06. I think the same software can be used, is it correct? Let me confirm just in case…
    • Resolved
    • Answered

  • ADS124S06: Error in measurement

    Resolved
    Part Number: ADS124S06 Hello, I’m trying to measure temperature with a PT1000 using ADS124S06 utiliting a 4-wire measurement. However, I’m experiencing a little bit of error in the measurement. When I try to substitute the PT1000 with a 1kOhm precision…
    • Resolved
    • Answered

  • ADS124S06: ADS124S06 Serial Communication Issues

    Resolved
    Part Number: ADS124S06 Hi, I have a custom PCB where the ADS124S06 communicates with a processor off the board over SPI. We have the CS# pin grounded, RESET# tied high, and I have probed the logic vdd and analog vdd pins, and they readout correctly. Below…
    • Resolved

Didn't find what you are looking for? Post a new question.