TI E2E support forums
TI E2E support forums
  • User
  • Site
  • Search
  • User
  • E2E™ design support >
  • Forums
    • Amplifiers
    • Audio
    • Clock & timing
    • Data converters
    • DLP® products
    • Enterprise Automation Integration
    • Interface
    • Isolation
    • Logic
    • Microcontrollers
    • Motor drivers
    • Power management
    • Processors
    • RF & microwave
    • Sensors
    • Site support
    • Switches & multiplexers
    • Tools
    • Wireless connectivity
    • Archived forums
    • Archived groups
  • Technical articles
    • Analog
    • Automotive
    • DLP® technology
    • Embedded processing
    • Industrial
    • Power management
  • TI training
    • Tech days
    • Online training
    • Live events
    • Power Supply Design Seminar
  • Getting started
  • 简体中文
  • More
  • Cancel


Search tips
Showing 584 results View by: Thread Post Sort by
  • RE: ADS124S08: Low pass filter sampling time optimization in ADS124S08

    Bryan Lizon86
    Bryan Lizon86
    Hi Zoe Yang, Can you please post the customer name in the Notes section of the Thread Tracking Toolkit? Bob is out this week so I can help support this question until he gets back. Bob asked for all ADC register settings being used for the measurement…
    • 8 days ago
    • Data converters
    • Data converters forum
  • ADS124S08: Data Reading problem (MISO Pin) with ADS124S08

    Rahul Gandhi
    Rahul Gandhi
    TI Thinks Resolved
    Part Number: ADS124S08 Hi, I have interface ADS124S08 With STM32F746 Controller. I have facing issued with register reading. I have checked on the CRO and Found that Whatever data i have sending its properly show on the MOSI Line but MISO Pin did not…
    • 21 days ago
    • Data converters
    • Data converters forum
  • RE: ADS124S08: ADS124S08

    Bob Benjamin
    Bob Benjamin
    Hi Zsolt, The low-side reference allows the measurement to be ratiometric. In the case of an RTD, the ratiometric measurement becomes a ratio of the RTD resistance to the the reference resistance. Why this is preferable is because the same excitation…
    • 1 month ago
    • Data converters
    • Data converters forum
  • ADS124S08EVM: ADS124S08

    Neel Shah
    Neel Shah
    TI Thinks Resolved
    Part Number: ADS124S08EVM Other Parts Discussed in Thread: ADS124S08 We have ADS124S08 EVM. We set analog input range from 0V to 5V. But at that time accuracy is not good as compared to vref=+/-2.5V. Could you please help me on this, why this has been…
    • 2 days ago
    • Data converters
    • Data converters forum
  • ADS124S08: ADS124S08 Schematic Review

    alikaan
    alikaan
    TI Thinks Resolved
    Part Number: ADS124S08 Hi, Could you please review the schematic ? I would like to use PT100 sensor for my application. Thanks . 910.36.ET.01.KT.100004.AB.pdf
    • 3 months ago
    • Data converters
    • Data converters forum
  • Answered
  • ADS124S08: Is it possible to use ADS124S08 instead of ADS124S06 with same software

    Shinichi Inoue
    Shinichi Inoue
    Resolved
    Part Number: ADS124S08 Other Parts Discussed in Thread: ADS124S06 , , ADS114S06 , ADS114S08 Dear Specialists, My customer is considering ADS124S08 as substitute for ADS124S06. I think the same software can be used, is it correct? Let me confirm just in case…
    • Resolved
    • 2 months ago
    • Data converters
    • Data converters forum
  • ADS124S08: Can the ADS124S08 have the same control as the AD7190 Channel Sequencer?

    Shinichi Inoue
    Shinichi Inoue
    TI Thinks Resolved
    Part Number: ADS124S08 Other Parts Discussed in Thread: ADS124S06 , Dear Specialists, My customer is considering ADS124S08 and ADS124S06 instead of AD7190. I would be grateful if you could advise. They’d like to confirm if ADS124S08 and ADS124S06 can do…
    • 2 months ago
    • Data converters
    • Data converters forum
  • ADS124S08: ADC doesn't read correct

    0_utq_0
    0_utq_0
    TI Thinks Resolved
    Part Number: ADS124S08 Hi I have ADS124S08 . I use 4 channel. All channels configure with 4 wire pt100. Some channels read correct, some channels don't read correct. For example, I measure with multimeter 100.5 ohm but when I try with ADS124S08, result…
    • 2 months ago
    • Data converters
    • Data converters forum
  • ADS124S08: To achieve a conversion time of 3ms or less (300SPS) each between two channels

    Shinichi Inoue
    Shinichi Inoue
    TI Thinks Resolved
    Part Number: ADS124S08 Other Parts Discussed in Thread: ADS124S06 Dear Specialists, My customer is considering ADS124S06 and has a question. I would be grateful if you could advise. --- I'd like to switch between two channels and achieve a conversion time…
    • 2 months ago
    • Data converters
    • Data converters forum
  • Answered
  • ADS124S08: Global chop in ADS124S08

    YOSHIHIKO KURUI
    YOSHIHIKO KURUI
    Resolved
    Part Number: ADS124S08 I have a question about the offset removal function of the ADS124S08 when global chop is enabled. If global chop is enabled, even if there is a large offset in the differential voltage input to the ADS124S08, is the offset removed…
    • Resolved
    • 7 months ago
    • Data converters
    • Data converters forum
>

Didn't find what you are looking for? Post a new question.

  • Ask a new question
About TI
Company News & events Investor relations Corporate citizenship Careers Contact us
Quick links
TI E2E™ design support forums Customer support center Packaging Quality & reliability TI university program myTI FAQ
Buying
Ordering resources Ordering help & FAQs BOM & cross reference tool Quick add to cart Authorized distributors
Connect with us

Texas Instruments has been making progress possible for decades. We are a global semiconductor company that designs, manufactures, tests and sells analog and embedded processing chips. Our products help our customers efficiently manage power, accurately sense and transmit data and provide the core control or processing in their designs.

Cookie policy Privacy policy Terms of sale Terms of use Trademarks Website feedback

© Copyright 1995-2023 Texas Instruments Incorporated. All rights reserved.