TI E2E support forums
TI E2E support forums
  • User
  • Site
  • Search
  • User
  • E2E™ design support >
  • Forums
    • Amplifiers
    • API solutions
    • Audio
    • Clock & timing
    • Data converters
    • DLP® products
    • Interface
    • Isolation
    • Logic
    • Microcontrollers
    • Motor drivers
    • Power management
    • Processors
    • RF & microwave
    • Sensors
    • Site support
    • Switches & multiplexers
    • Tools
    • Wireless connectivity
    • Archived forums
    • Archived groups
  • Technical articles
  • TI training
    • Tech days
    • Online training
    • Live events
    • Power Supply Design Seminar
  • Getting started
  • 简体中文
  • More
  • Cancel


Search tips
Showing 21 results View by: Thread Post Sort by
  • ADS1257: Typical Application Questions

    Jeremy Styma
    Jeremy Styma
    TI Thinks Resolved
    Part Number: ADS1257 Tool/software: Looking to use the typical application circuit ( Fig 65 ) to sample a 4-20mA pressure transducer in an industrial environment. The typical application samples at 10SPS for 50/60hz rejection. In the case where a higher…
    • 11 months ago
    • Data converters
    • Data converters forum
  • Answered
  • ADS1257: ADS1257 Measurement error (gain error)

    kiyoshi umezawa
    kiyoshi umezawa
    Resolved
    Part Number: ADS1257 Hello. I will repost in English. ADS1257 is used for differential measurement with 2000SPS, PGA = 2, ACAL ENABLE, BUF Disabled settings. 2.4V is input to AIN1 and REF from the high precision reference power supply. Input 2…
    • Resolved
    • over 3 years ago
    • Data converters
    • Data converters forum
  • ADS1257:ADS1257 計測誤差について

    kiyoshi umezawa
    kiyoshi umezawa
    TI Thinks Resolved
    Part Number: ADS1257 はじめまして。 ADS1257を2000SPS,PGA=2,ACAL ENABLE,BUF Disabled設定で差動計測で使用しています。 AIN1,REFには基準電源から2.4Vを入力。 AIN0には別の基準電源から2.4V~4.4Vを入力。 AIN0、AIN1にそれぞれ2.4Vを入力した場合、計測値は0.01mVとなります。 AIN0=4.4V、AIN1=2.4Vを入力(差動入力電圧誤差0.1mV)した場合、計測値は1.984Vとなり、誤差が16mVと大きな値を示しています…
    • over 3 years ago
    • Data converters
    • Data converters forum
  • RE: ADS1257: Setup ADS1257 Concerns

    Christopher Hall
    Christopher Hall
    Hi Khoi, Setting up an MCU's SPI peripheral shouldn't be an entirely manual process if you are working with an SPI peripheral. Yes there are some timing requirements that you need to pay attention to (such as adding a delay after setting /CS low, or…
    • over 7 years ago
    • Data converters
    • Data converters forum
  • Answered
  • RE: ADS1257: Clock Source for ADS1257

    Khoi Ly10
    Khoi Ly10
    Resolved
    Sorry, I mean the crystal oscillator (the one similar to that in your provided links). A crystal oscillator has 4 pads. For a microcontroller, I usually connect pad 1 to OC1 and Pad 3 to OC2 of the microcontroller. But the ADS1257 only has one pin CLKIN…
    • over 7 years ago
    • Data converters
    • Data converters forum
  • Answered
  • ADS1257: Basic questions about specifications

    Takumi Suzuki1
    Takumi Suzuki1
    Resolved
    Part Number: ADS1257 Hi, Let me ask you some basic questions about ADS1257 as below. Q1) INL specifications Following is a part of System performace table (data sheet page 7) Q1-1) About INL, the value is only "+", there is no "-" value, …
    • Resolved
    • over 7 years ago
    • Data converters
    • Data converters forum
  • ADS1257: Single-Cycle settled conversion

    Takumi Suzuki1
    Takumi Suzuki1
    TI Thinks Resolved
    Part Number: ADS1257 Other Parts Discussed in Thread: ADS1248 Hi, Let me ask you a question about "Single cycle" . There is a description on the datasheet as below. (Red) Does this mean "Single-Shot Mode", right? I do not understand why is …
    • over 7 years ago
    • Data converters
    • Data converters forum
  • Answered
  • ADS1257: How do you think of "Single-Cycle Settled Conversions"?

    Takumi Suzuki1
    Takumi Suzuki1
    Resolved
    Part Number: ADS1257 Other Parts Discussed in Thread: ADS124S08 I would like to ask you about very basic question, "Single-Cycle Settled Conversions"? Basically, a delta-sigma A/D is used as "continuous" conversion due to internal digital filter. …
    • Resolved
    • over 7 years ago
    • Data converters
    • Data converters forum
  • Answered
  • ADS1257: INDUSTRIAL TEXAS INSTRUMENTS BASED IEPE SYSTEM SCHEMATI REVIEW

    Ignacio Diz Castro
    Ignacio Diz Castro
    Resolved
    Part Number: ADS1257 Please review this schematic Notes: 1) ADS1257 does not allow to place beads at power input so 4 ldo ics were placed 2) General comments, design suggestions 4214.FAD_TI.pdf
    • Resolved
    • over 7 years ago
    • Data converters
    • Data converters forum
  • Answered
  • RE: ADS1257 Single ended measurement

    Joachim Wuerker
    Joachim Wuerker
    Resolved
    Hi Peter, I wanted to let you know that the complete datasheet of ADS1257 is online now. I hope you are still happy with the ADS1257 and are making good progress with your development. Regards,
    • over 9 years ago
    • Data converters
    • Data converters forum
>

Didn't find what you are looking for? Post a new question.

  • Ask a new question