Search tips
Showing 458 results View by: Thread Post Sort by

  • ADS1258: ADS1258 working

    TI Thinks Resolved
    Part Number: ADS1258 Hi I am working out interface with ADS1258 with my controller, I am using internal SPI. tracing only SPI working and initializing look like works ok. But I am not able to read channel. My application is to read all 16 channel one…
    • Answered

  • ADS1258-EP: V62/09626-02XE and V62/09626-02YE

    Resolved
    Part Number: ADS1258-EP Hi All, I have some questions about ADS1258-EP. What is the difference between V62/09626-02XE and V62/09626-02YE? Best Regards, Ishiwata
    • Resolved

  • ADS1258: ADS1258 Channel Data Read Direct Questions

    TI Thinks Resolved
    Part Number: ADS1258 Tool/software: Hi, I am working on the ADS1258 and I have questions about the Channel Data Read Direct command. First, I am sending a register write command (the first three bits are "011"=Register Write Command) in order to configure…
    • Answered

  • ADS1258-EP: Logic level for external clock

    Resolved
    Part Number: ADS1258-EP Other Parts Discussed in Thread: ADS1258 Tool/software: Hi, my customer wants to use an external clock, but is not sure which logic level height is needed for the clock-signal. Can you provide further requirements for the clock…
    • Resolved

  • TMS320F28379D: ADS1258:READ CONFIG0 DEFAULT REGISTER VALUE

    Part Number: TMS320F28379D Other Parts Discussed in Thread: ADS1258 Tool/software: Hello, I had created a thread earlier, but there was very little response on it, so I have created a new thread here. I am using the TMS320F28379D controller, which I…
    • Answered

  • ADS1258-EP: Identification via ID or serial number over SPI

    Resolved
    Part Number: ADS1258-EP Other Parts Discussed in Thread: ADS1258 Tool/software: Hi, Is there an option to identify an ADC via an ID or serial number over SPI? My customer is open for other solutions to identify each ADC individually. Thanks
    • Resolved

  • TMS320F28379D: ADS1258: AIN0 data not read using TMS320 controller.

    TI Thinks Resolved
    Part Number: TMS320F28379D Other Parts Discussed in Thread: ADS1258 , Tool/software: I used the ADS1258 EVM software to verify the ADC output values for known input voltages and prepared an Excel table as shown below. Could you please check if the formulae…
    • Answered

  • ADS1258-EP: Conversion latency lower then expected

    Resolved
    Part Number: ADS1258-EP Other Parts Discussed in Thread: ADS1258 Tool/software: I am reading channels AIN0-15 and all SYSRED channels which comes out to 21 channels in auto-scan mode. from the ADS1258-EP datasheet I calculated my sample rate from the…
    • Resolved

  • ADS1258: Multiple Strain Gauge (40 Channel)

    TI Thinks Resolved
    Part Number: ADS1258 Other Parts Discussed in Thread: ADS131E06 , ADS131E08 , ADS127L11 Tool/software: Greetings Community, I need advice on data logging multiple ADCs and/or ADC Channels to interface 40+ Strain Gauge Values on an MCU that can show…

  • ADS1258: ADS1258

    TI Thinks Resolved
    Part Number: ADS1258 Hi TI, We have design based ADS1258IRTCR We have problem of reading external ADC input 16 Ch Single ended or DIFF - all read are not correct close to ~0V We succeed to read SYSRED Internal measurements : REF - GAIN - TEMP…

Didn't find what you are looking for? Post a new question.