Search tips
Showing 26 results View by: Thread Post Sort by
    Answered

  • ADS125H01: Background to why CRC is implemented

    Resolved
    Part Number: ADS125H01 Other Parts Discussed in Thread: ADS125H02 Tool/software: Dear Specialists, My customer is considering ADS125H02 and has a question about CRC. I would be grateful if you could advise. --- I would like to confirm the CRC built into…
    • Resolved

  • ADS125H01: output conversion

    Part Number: ADS125H01 Tool/software: Hello, I am having an issue with the output conversion from ADS125H01. I am applying a 49 mV differential signal at input (+5.030 V to AINP, +4.981 V to AINN), and at the output after conversion I am receiving approximately…
    • Answered

  • ADS125H01: ADS125H01 CRC Problem

    Resolved
    Part Number: ADS125H01 Other Parts Discussed in Thread: ADS125H02 Tool/software: Hi! I'm using the ADS125H01 with an STM32H745. I have converted the library that is provided to the stm32 and setup SPI. My SPI setup is: I am executing adcStartu…
    • Resolved
    • Answered

  • ADS125H01: About Noise Characteristics

    Resolved
    Part Number: ADS125H01 Other Parts Discussed in Thread: ADS125H02 Tool/software: Hi team, The ADS125H02 has a list of noise characteristics in Tables 1 and 2, but the ADS125H01 does not. Can we assume that these characteristic tables are the same? Regards…
    • Resolved
    • Answered

  • ADS125H01: Relationship between external clk and sampling rate

    Resolved
    Part Number: ADS125H01 Tool/software: Dear Specialists, My customer is considering ADS125H01 and has a question about relationship between external clock and sampling rate. I would be grateful if you could advise. --- I want to input a 6.144MHz external…
    • Resolved
    • Answered

  • ADS125H01: External Voltage Reference for ratiometric strain gauge measurement

    Resolved
    Part Number: ADS125H01 Tool/software: Dear Specialists, My customer is considering External Voltage Reference for ratiometric strain gauge measurement with ADS125H01. External Voltage is 15V and current is 40mA. According to the application note https…
    • Resolved

  • ADS125H01: Sample at 60Hz with sync4 in pulse conversion mode?

    TI Thinks Resolved
    Part Number: ADS125H01 I have a number of these A/D's (ADS125H01) that I want to keep in sync with each other. They are run off a common clock (7.3728MHz) and they have all their start pins tied together. I was intending to start all the converter…
    • Answered

  • ADS125H01: Power loss on HV_AVDD and AVDD results in register loss?

    Resolved
    Part Number: ADS125H01 Hello- I have been working with my ADS125H01 design (schematic attached) and I noticed that if I power down the HV_AVDD (+12V) and AVDD (+5V) rails, my register settings are lost and need to be re-set. I couldn't find anything in…
    • Resolved
    • Answered

  • ADS125H01: When is ADS125H01EVM available

    Resolved
    Part Number: ADS125H01 Other Parts Discussed in Thread: ADS125H02 , ADS125H02EVM Dear Specialists, My customer is interested in ADS125H01 and wants to obtain EVM. But I couldn't find it. Could you please let us know when is ADS125H01EVM released. I…
    • Resolved

  • ADS125H01: ADS125H01

    Part Number: ADS125H01 ADS125H01 Main Status (STATUS0) Register (address = 01h) [reset = 01h]，shows that there is a Reference Voltage Alarm (bit three of this register),This bit sets when the reference voltage falls below < 0.4 V (typical). The alarm…

Didn't find what you are looking for? Post a new question.