Filter by Reset

All
Forums (26)
Technical Articles (0)
Wikis (0)
Files (0)
Groups (0)
FAQ
  • Show only FAQs
Reply
  • Resolved
  • TI thinks resolved
  • Answer suggested
  • Has replies by TI employees
  • Has replies
Creation Date
  • Any
  • Past Week
  • Past Month
  • Past 3 Months
  • Past 6 Months
  • Past Year
From
To


Search tips
Showing 26 results View by: Thread Post Sort by
    Answered

  • ADS125H01: Can the high voltage analog supplies be driven as single ended (HV_AVss = 0V)?

    Resolved
    Part Number: ADS125H01 Other Parts Discussed in Thread: ADS125H02 , Hi There- I've been working with the ADS125H01 and its sister part ADS125H02 in a load cell application. I have 12V, 5V, and 3.3V available on my board, and the load cell is excited at…
    • Resolved

  • ADS125H01: ADS125H01 cannot read and write registers whose addresses exceed 10H, even if CS2(low active) has been pulled down.

    TI Thinks Resolved
    Part Number: ADS125H01 ADS125H01 cannot read and write registers whose addresses exceed 10H, even if CS2(low active) has been pulled down. Figure 1 below is the write register function (WREG Command), and Figure 2 is the SPI read-write array for single…
    • Answered

  • ADS125H01: Vin range

    Resolved
    Part Number: ADS125H01 Hello, I would like to make clear the input range, I use +/-15V supply and do not ground my system and the measured one, only the differential input + is connected to 18V and the diferential input - is connected to -1V. It means…
    • Resolved

  • ADS125H01: 24-Bit  ΣΔADC With Rail-to-Rail OPAMP

    TI Thinks Resolved
    Part Number: ADS125H01 Please recommend a 24 bit ΣΔ ADC With Rail-to-Rail OPAMP ADC. In addition, it requires small volume, low price and no requirement for sampling rate.

  • RE: ADS8588S: ADC and AFE recommendation

    Hi Chandra, OK - the ADS125H01 will not hit the target sampling rate. On that front, the 250 kS/s requirement is for all 8/16 channels at 250K (31.25/15.625 kS/s per channel) or all 8/16 channels at 250 kS/s per channel?

  • ADS125H01: Need to measure uA current ADC solution

    TI Thinks Resolved
    Part Number: ADS125H01 Other Parts Discussed in Thread: ADS1260 Hi team, My customer would like to design one solution that can measure uA current measurement solution. The specification is measuring 0~50mA current and the current shunt resistor will be…

  • ADS125H01: ADC design support

    TI Thinks Resolved
    Part Number: ADS125H01 Other Parts Discussed in Thread: ADS1262 Hi I'd like to used ADS125H01 which is 32bit ADC and our signal is include 60Hz frequency . Unfortunately, I found some comment that 50Hz and 60Hz rejection function in data sheet of…

  • ADS125H01: When does ADS125H01 plan to RTM and further questions

    TI Thinks Resolved
    Part Number: ADS125H01 Hi DC team, I'm posting this question on behalf of my customer. These questions are regarding ADS125H01. 1. We want to run it (CLKIN) from 2.048 MHz derived from our phase locked to GPS TCXO. It would be configured to produce…

  • RE: ADS1220: Data Acquisition System Resolution Problem

    Hi Fatih, Fatih Cavdarci said: Can the mean filter or other improve noise free bits? The ADS1220 is a delta-sigma ADC, which means lower noise results are achieved with lower date rates due to higher over-sampling ratios. The following article helps explain…

  • ADS1115: 24V sensor read with ADC

    TI Thinks Resolved
    Part Number: ADS1115 Other Parts Discussed in Thread: ADS125H01 Tool/software: Hi, I could not find suitable IC for my application so I decided to open this thread. I would like to read 0-24V sensor output with ADC for my MCU. Is there any suggested IC…
1 2 3

Didn't find what you are looking for? Post a new question.