Search tips
Showing 217 results View by: Thread Post Sort by
    Answered

  • ADS127L01: ADS127L01 - REXT resistor value

    Resolved
    Part Number: ADS127L01 Good day Colleagues, According to the datasheet REXT resistor has to be 60,4kOhm +/-1% (for HR or LP mode). Is there a reason for that why it has to be so precise? What happens if the resistor deviates from that value? For example…
    • Resolved

  • ADS127L01: ADS127L01 START pin with a resistor

    TI Thinks Resolved
    Part Number: ADS127L01 Good day Colleagues, According to the ADS172L01 data sheet all hardware mode pins shall be pulled to DVDD or DGND via 100kOhm resistors, but START pin. Also in the EVAL-board the START pin is pulled to DVDD via a 100kOhm resistor…

  • ADS127L01: ADS127L01 DIGIKEY AND MASTER MARKING

    TI Thinks Resolved
    Part Number: ADS127L01 Dear Sir/Madam Good day! I have bought a TI part ADS127L01IPBS from Digikey,but our customer feedback said the TI LOGO on the top marking is different as his Master sample,pls check pictures below. And he said X-RAY also different…

  • ADS127L01: How connect ADS127L01 or ADS127L11 with STM32

    TI Thinks Resolved
    Part Number: ADS127L01 Other Parts Discussed in Thread: ADS127L11 Hi TINA TI experts, Do you have any idea in how to connect ADS127L01 with STM32 via SPI in order to read data converted by ADC? Is there any library of this ADC that can help me to do…

  • ADS127L01: ADS127L01 module not found in TINA TI

    TI Thinks Resolved
    Part Number: ADS127L01 Other Parts Discussed in Thread: TINA-TI , ADS127L11 Hi TI experts, I want to design an ADS based on ADS127L01 but can’t find the schematic of this component on TINA TI software. If someone has this schematic, don’t hesitate to share…
    • Answered

  • RE: ADS127L01: can not read registers through SPI

    Resolved
    Hello Keith, Thank you for your response, I can now read data. Best regards,
    • Answered

  • ADS127L01: Is ADS127L01 suitable for both static and dynamic strain gauge measurement?

    Resolved
    Part Number: ADS127L01 Other Parts Discussed in Thread: ADS124S08 , ADS1261 , , ADS127L11 , , THS4551 We are designing a strain gauge based sensing circuit and need to make both static (signal unchanged or slowly changing around 30-60 seconds) and dynamic…
    • Resolved
    • Answered

  • ADS127L01: The device does not work properly (data is wrong, DRDY is wrong)

    Resolved
    Part Number: ADS127L01 Pattern: the VLP Sampling rate: 64KSPS, DATA interface adopts SPI, configured in the form of three bytes (24bit) data upload (i.e. Disable status word), In the form of Daisy chain, the circuit is shown in Figure 1, 2 and 3: The phenomenon…
    • Resolved

  • RE: ADS127L01: how to get the 1.34 µVRMS of input-referred noise in ADS127L01 d/s

    Hi Steven, These numbers were measured in the lab by shorting the inputs (0V input) and recording a large number of ADC conversion readings (16k), and then calculating the 1-sigma value of the data set. Many of the newer EVM's provide this calculation…
    • Answered

  • ADS127L01: Register and Capacitor

    Resolved
    Part Number: ADS127L01 Other Parts Discussed in Thread: TIDA-01471 , Hi, I have any questions. 1. Please tell me the reason why R2, R3 and R4 described in "Schematic" of TIDA-01471 are connected. https://www.ti.com/tool/TIDA-01471 If the reason…
    • Resolved

Didn't find what you are looking for? Post a new question.