Search tips
Showing 68 results View by: Thread Post Sort by
    Answered

  • ADS1282-SP: ADS1282-SP Final FSR

    Resolved
    Other Parts Discussed in Thread: ADS1282-SP Hello Everyone I've configured ADS1282-SP as below: AVDD=5V AVSS=0V VREF=VREFP-VREFN= 2.5-0 = 2.5V Signal: A DC signal in the range of 100mV - 150mV feeds to the diffential input and always AVINP > AVINN…
    • Resolved

  • ADS1282-SP: ADC Error Charachtristics is not clear

    TI Thinks Resolved
    Part Number: ADS1282-SP Other Parts Discussed in Thread: ADS1220 , , ADS124S08 Tool/software: Dear TI Technical Community, As throughphully described in refrences below [1-3], estimating total error of RTD-based temperature measurment using precise ADCs…
    • Answered

  • ADS1282-SP: Calculation of tDR after Reset

    Resolved
    Part Number: ADS1282-SP Tool/software: Dear all, According to Datasheet section 7.8 Reset Timing Requirement, tDR after reset will consist of 1/fData (big portion) and 1/fClk (small portion). I assume that the calculation for tDR after reset takes the…
    • Resolved
    • Answered

  • ADS1282-SP: Unclear parameter in Datasheet Rev.B

    Resolved
    Part Number: ADS1282-SP Tool/software: Hi, in ADS1282-SP Datasheet Rev.B page 9, section 7.7, the parameter tDR is defined. Below you see a reference to Table 21 for SINC filter while an equation is provided for FIR filter respectively (which I think…
    • Resolved

  • ADS1282-SP: 5962L1423101VXC WEIGHT

    TI Thinks Resolved
    Part Number: ADS1282-SP Tool/software: Hi, What is the weight (grams) of 5962L1423101VXC (ADS1282-SP)? Thanks

  • ADS1282-SP: Post Radiation and Aging

    TI Thinks Resolved
    Part Number: ADS1282-SP Hi team, I am doing a worst-case analysis for the acquisition channel of my board. I should repeat them in 3 conditions: BOL Begin Of Life BOL+Thermal drift EOL End of Life My using the ADS1282-SP (5962L1423101VXC), in the datasheet…
    • Answered

  • ADS1282-SP: Clock Jitter requirement

    Resolved
    Part Number: ADS1282-SP The datasheet mentions that a low-jitter clock is essential for optimum performance, but doesn’t recommend any typical values for jitter. What jitter is recommended for a DC measurement (essentially a RTD temperature measurement…
    • Resolved
    • Answered

  • ADS1282-SP: Pulse SYNC mode / SPI

    Resolved
    Part Number: ADS1282-SP Other Parts Discussed in Thread: ADS1282 I had some questions about the ADS1282-SP. There was a pin called sync. I saw that there are 2 modes of operation, pulse sync mode and continuous sync mode. If we use pulse sync mode,…
    • Resolved

  • ADS1282-SP: Serial data protocol model

    Part Number: ADS1282-SP Other Parts Discussed in Thread: ADS1282 Hello there, I am currently developing a FPGA design to control and retrieve data from the ADS1282-SP converter. Is there a functional stub or any other module of reference for the articulated…
    • Answered

  • ADS1282-SP: ADS1282-SP - Single Event Latchup (SEL) at 85°C

    Resolved
    Part Number: ADS1282-SP Dear All, it's stated that "Single Event Latchup (SEL) Immune to LET = 60 MeV-cm 2 /mg at 85°C", but in the Report SBAA222 I cannot find any evidence about the relevant test data with this LET. The max LET in Table8…
    • Resolved

Didn't find what you are looking for? Post a new question.