Search tips
Showing 77 results View by: Thread Post Sort by
    Answered

  • ADS130E08: Sinc filter used

    Resolved
    Part Number: ADS130E08 Tool/software: Hello, I have a question regarding the digital filter unit used in the ADS130E08. On page 17 a sinc3 filter equation ist shown. Those filters causes a systematic delay of three samples (see page 18; 3*t_dr settling…
    • Resolved

  • ADS130E08: ADS131E08: Sample code

    Part Number: ADS130E08 Other Parts Discussed in Thread: TMS320F28377D , ADS131E08 Tool/software: Can you please share the source code that runs on the TMS320F28377D DSP on ADS130E08 Performance Demonstration Kit？

  • ADS130E08: Single-ended input range

    TI Thinks Resolved
    Part Number: ADS130E08 I'm a little confused by the stated analog input range and diagram when ADS130E08 is configured for single-ended input. Figure 18 shows the input range as CM voltage (INN) +/- Vref/2. Ignoring CM range concerns and assuming…
    • Answered

  • ADS130E08: Internal Test Signal

    Resolved
    Part Number: ADS130E08 Customer is developing driver SW to read data from ADS130E08. Trying to use the internal test signal as a quick check of the SW readback and want to verify our understanding of what the results should look like. With Vref = 2…
    • Resolved

  • ADS130E08: Single-ended inputs and expected conversion codes

    TI Thinks Resolved
    Part Number: ADS130E08 Another engineer and I are in disagreement on how this device works when configured for single-ended inputs. I have this part with the following configuration: AVDD = 5V AVSS = 0V (ground) DVDD = 3.3V DGND = 0V (ground…

  • ADS130E08: Help on DSP

    Part Number: ADS130E08 Other Parts Discussed in Thread: ADS131M04 , ADS131E08 , , TIDA-010037 Hi, I'm having some difficulty with the specification of a DSP. How to know the correct parameters like clock, bits and etc? Are there some recommended DSP…

  • ADS130E08: ADS9817 can be used as alternative? Or any suggestions?

    Part Number: ADS130E08 Other Parts Discussed in Thread: ADS9817 Hi Experts, Seeking your guidance please: Customer realized that as part of the realization of a test means requiring the measurement of 8 voltages he had identified the ADC ADS130E08…
    • Answered

  • ADS130E08: Isolation of SPI bus

    Resolved
    Part Number: ADS130E08 Other Parts Discussed in Thread: ISO7731 Hi Team, Our customer would like to know when to isolate the SPI bus of ADS130E08 from the microcontroller? He also wants to know if TVS diodes on ADC inputs are enough to stop EFTs and…
    • Resolved
    • Answered

  • ADS130E08: ADS130E08

    Resolved
    Part Number: ADS130E08 Hi, I am using ADS130E08 as ADC in my project. if we read the datasheet its written that if VINP-VINN is greater than or equal to Vref then the digital output will be 7FFF. in my application VINP(max):2.85V, VINN:1.65V, VIN…
    • Resolved
    • Answered

  • ADS130E08: Maximum and minimum analog input voltage

    Resolved
    Part Number: ADS130E08 Hello, I'm developing a device that needs to read data from -4V to 4V (or 2.828Vrms). According to the following table on the datasheet that is possible. But when reading other sections of the datasheet I ended up getting…
    • Resolved

Didn't find what you are looking for? Post a new question.