Search tips
Showing 53 results View by: Thread Post Sort by

  • ADS131B04-Q1: SPI Timing

    TI Thinks Resolved
    Part Number: ADS131B04-Q1 Tool/software: When the MCU communicates with the ADS131B04 SPI, it is observed through the oscilloscope that the DRDY signal is mostly kept low in the SPI timing, and there will be a jump when there is data transmission, is…

  • ADS131B04-Q1: reading RESET bit of STATUS active '1' while no reset commanded or triggered via reset pin

    Part Number: ADS131B04-Q1 Tool/software: while regular operation of sequential reading of data, i'm quite regularly observe (about every 25ms) status register with reset bit being active (set) while zeroes and garbage appears on channels. keeping reset…
    • Answered

  • ADS131B04-Q1: RESET bit of STATUS reg is '1' every reading while reset pin is pegged to DVDD and null command issued

    Resolved
    Part Number: ADS131B04-Q1 Tool/software: does it normal behavior of the bit of the STATUS?
    • Resolved

  • ADS131B04-Q1: Provide the time sequence diagram of sending NULL instructions

    Part Number: ADS131B04-Q1 Tool/software: Dear Can you provide the time sequence diagram of sending NULL instructions (according to 24bit) ? and I will compare whether the instructions I sent are normal. Now after the ADC is powered on, the DRDY pin…
    • Answered

  • ADS131B04-Q1: Negative voltage input, large differential output voltage error

    Resolved
    Part Number: ADS131B04-Q1 Other Parts Discussed in Thread: ADS131M04-Q1 Tool/software: Dear Experts, We are using ADS131B04 for sampling, currently using battery P+as the ground ISOP+of the ADC chip. As shown in the diagram below, AIN0P and AIN0N sample…
    • Resolved
    • Answered

  • ADS131B04-Q1: Latency

    Resolved
    Part Number: ADS131B04-Q1 Hi team, My customer want to know the latency of ADS131B04-Q1. I read below article. Could you provide the delay table for ADS131B04-Q1? https://www.ti.com/lit/wp/slyy095a/slyy095a.pdf Best Regards,
    • Resolved

  • ADS131B04-Q1: Scenarios for use and how to use the calibration function

    Part Number: ADS131B04-Q1 Tool/software: Regarding the calibration function of the ADS131B04, can you provide a scenario for using this function, when you need to use this function, and do you need to put this function in a loop when using it? If so,…

  • ADS131B04-Q1: Raspberry Pi addon

    TI Thinks Resolved
    Part Number: ADS131B04-Q1 Other Parts Discussed in Thread: ADS1115 Team, my customer is using ADS1115 and wants to move to ADS131B04-Q1 due to higher sampling rate. Do we have something like this (https://github.com/MediaMongrels-Ltd/RPi-LINX-Addons…
    • Answered

  • ADS131B04-Q1: Common mode voltage range of input channels

    Resolved
    Part Number: ADS131B04-Q1 Hi, In our application we would like to measure battery pack voltage (0- 500V) by a resistive divider and make use of the AMC1311B (isolated amplifier). The AMC1311B provides a differential output to the ADC input channel but…
    • Resolved

  • ADS131B04-Q1: Component info

    TI Thinks Resolved
    Part Number: ADS131B04-Q1 Good afternoon, Our component library contains some products from Texas Instruments for which we need the following information: « Thermal shock » - « Cycles » The components are: Manufacturer Manufacturer_Order_Number…

Didn't find what you are looking for? Post a new question.