Search tips
Showing 101 results View by: Thread Post Sort by
    Answered

  • ADS131E08: looking for sample code for the ads131e04 but ads131e08 would do

    Resolved
    Part Number: ADS131E08 hello - could you send me the sample code or access. my profile email is fine thanks Mark
    • Resolved
    • Answered

  • ADS131E04: 24bit resolution not fully usable

    Resolved
    Part Number: ADS131E04 Other Parts Discussed in Thread: ADS131E08 We are using a ADS131E04 in 24bit 16ksps mode. The values we get seem to be valid on all channels apart from the occasional extreme outlier, but we can deal with those. But if we look at…
    • Resolved
    • Answered

  • ADS131E04: Best way to use the ADC with 0-1.8 V single ended inputs

    Resolved
    Part Number: ADS131E04 Other Parts Discussed in Thread: ADS131E08 Hello, I have to use ADS131E04 in order to acquire data from a 3-axes accelerometer. The sensor outputs data in the 0-1.8 V range (nominally 0.1 to 1.7 V), in single-ended mode. What is…
    • Resolved

  • ADS131E04: Fast power up type ADC

    TI Thinks Resolved
    Part Number: ADS131E04 Other Parts Discussed in Thread: ADS131E08S , ADS131A04 We have used ADS131E04 ADC in our one product. I would like to reuse same for another product we are starting design. Only one parameter is not suitable as Power up timing of…
    • Answered

  • ADS131E04: Differences between A, E, and M for 60Hz AC Power Measurements

    Resolved
    Part Number: ADS131E04 Hi, I've looked through the datasheets for all three types, and am curious which ADC would work best for measuring AC Power (120-347VAC, voltage-divided down) at 60Hz. Having a PGA is not a big concern for me, as I will put all…
    • Resolved

  • ADS131E04: Malfuntioning after the dip in voltages

    TI Thinks Resolved
    Part Number: ADS131E04 Hi, If any dip in the DVDD(3.3V) is happened to the IC, malfunctioning happening the timing. above waveform shown the dip pattern for the IC. It lasts for only 80mS. and one more observation is the system behaves incorrectly if…

  • ADS131E04: After the dip in the supply voltage , some times not able to read device ID "0xD0"

    TI Thinks Resolved
    Part Number: ADS131E04 Some times after power interruptions Controller not able to read Device ID. Normally i am getting "0xD0". But after these mentioned times it is reading "0x00". Supply is stable during this reading time. SPI frequency = 8MHz…
    • Answered

  • ADS131E04: Single ended input and input voltage range

    Resolved
    Part Number: ADS131E04 Other Parts Discussed in Thread: ADS131M04 Hi, I want to clarify some points regarding my input signal to ADS131E04. ADS131E04 has a supply voltage of AVDD = 3.3 V and AVSS = 0 V. VREF is set to 2.4 V internal. Assuming gain is…
    • Resolved

  • ADS131E04: Problems reading the registers and the data by an Arduino Due

    TI Thinks Resolved
    Part Number: ADS131E04 Other Parts Discussed in Thread: ADS131E08EVM-PDK Hello, everyone, I would like to read out the ADS131E04 with an Arduino Due via SPI. Unfortunately, I have little previous experience, and this is my first project with an SPI communication…
    • Answered

  • ADS131E04: Internal oscillator not working

    Resolved
    Part Number: ADS131E04 Other Parts Discussed in Thread: ADS131E08 Hello, I am having a problem with the ADS131E04. Internal oscillator on the device is not working. CLKSEL pin is connected to 3.3 V and CLK to GND. Device does not respond at all. If I…
    • Resolved

Didn't find what you are looking for? Post a new question.