Search tips
Showing 7,150 results View by: Thread Post Sort by

  • ADS1261-EXCEL-CALC-TOOL: RTD PT100 MEASUREMENT

    TI Thinks Resolved
    Part Number: ADS1261-EXCEL-CALC-TOOL Other Parts Discussed in Thread: ADS1261 , ADS1261EVM , DELTASIGMAEVAL-GUI HI Team, Below is the setup: Hardware Setup: Board: ADS1261 EVM Sensor: 3-wire PT100 RTD Wiring: Red wire → AIN0 White wire…
    • Answered

  • ADS124S08-EXCEL-CALC-TOOL: Unexpected behavior of the RTD Calculator accuracy estimation

    Resolved
    Part Number: ADS124S08-EXCEL-CALC-TOOL Other Parts Discussed in Thread: ADC-RTD-CONFIG-CALC , Dear Support, While using the RTD Calculator for my circuit, I noticed a behavior that I am unable to explain. The accuracy calculated by the tool is exactly…
    • Resolved

  • LMG5126: LMG5126-CALC excel sheet and Webench

    Part Number: LMG5126 The maximum switching frequency for my design on WEBENCH with the LMG5126 will only go to 800khz max. The CALC excel sheet allows me to go to 2000 or higher, but there is no efficiency chart in the excel sheet, which is different…

  • ADS1220-EXCEL-CALC: PSpice Simulation files for ADS127L01

    TI Thinks Resolved
    Part Number: ADS1220-EXCEL-CALC Other Parts Discussed in Thread: ADS1158 , ADS127L11 Hello I am looking for TINA spice or PSpice .LIB files for the ADS127L11, or ADS1158 or any of the similar ADCs which use Delta Sigma modulation. Do these files exist…

  • TPS24710: Excel design tool limitation

    TI Thinks Resolved
    Part Number: TPS24710 Other Parts Discussed in Thread: TIGER Hi, I used the TPS24710 excel design tool (slvc566f.zip, www.ti.com/.../SLVC566) and my cusotmer is using MOSFET with 700A @ 100uS for SOA curve, but the excel tool cannot enter 700A. Is it…
    • Answered

  • ADS1220-EXCEL-CALC: R/C charger bank, does R include the output impedance of the amplifier

    Resolved
    Part Number: ADS1220-EXCEL-CALC Other Parts Discussed in Thread: ADS1220 , Normally for SAR ADC input. A R/C charger bank is required. When consider the R, does that include the output impedance of the amplifier(if use an amplifier to drive the SAR ADC…
    • Resolved

  • TPS1685-CALC: Issuw with the simulation tools

    TI Thinks Resolved
    Part Number: TPS1685-CALC Other Parts Discussed in Thread: TPS1685 We tried to use the simualtion file to test overcurrent protection and the Vout is not responsding as expected. Could you be able to check if the simulation model of TPS16851 is the…

  • TPSM63610-DESIGN-CALC: Part is Not available in the design tool

    Part Number: TPSM63610-DESIGN-CALC Other Parts Discussed in Thread: TPSM5D1806 Dear TI Team, I want to generate 3.3V & 2.5V from 6V by using the power module TPSM5D1806MRDBR-ET. But this part is not available in the TI simulation tool (web bench & Tina…

  • LM51770-Q1: LM51770 Excel design tool - Loop compensation

    TI Thinks Resolved
    Part Number: LM51770-Q1 Other Parts Discussed in Thread: LM51770 Hi TI, I have a 250W buck-boost converter with the following specifications: Vin: 18V – 32V Vout: 40V, 28V, or 12V Frequency : 1MHz. Load: 6.25 ohms I'd like to know the…

  • LP8865C-Q1: simulation excell tool to compare efficiency

    Part Number: LP8865C-Q1 Hello, I am looking to improve an existing design with higher efficiency buck driver Since we are targeting low budget design I have stopped on LP8865C-Q1 and want to check the different results for efficiency in the full supply…

Didn't find what you are looking for? Post a new question.