Search tips
Showing 13 results View by: Thread Post Sort by

  • ADS42LB49EVM: ADS42LB49EVM do not work at normal operation

    Part Number: ADS42LB49EVM I am using Kintex-7 to capture data from ADS42LB49EVM. My main board is XC7K325T and ADS42LBx9 GUI is used to configure the ADC. In my design, the output data is at DDR mode and data is config at 2' compliment. INAP and INBM…
    • Answered

  • ADS42LB49EVM: ADS42LB49EVM Rev B schematic

    Resolved
    Part Number: ADS42LB49EVM Other Parts Discussed in Thread: ADS42LB49 , ADS42LB69 Hello, I am looking for ADS42LB49EVM Rev B schematic and couldn't find it on TI website. I am using the eval board with FMC Rev D and is connected to Xilinx FPGA board…
    • Resolved
    • Answered

  • ADS42LB49EVM: Using SPI with 2.5 volts

    Resolved
    Part Number: ADS42LB49EVM Hello, I am planning to configure ADS42LB49EVM with an FPGA, the FPGA IO bank is using 2.5 volts. Will the serial interface work with 2.5v? I have noticed the ADC can wok with 1.8 and 3.3 cmos levels but I didn't find anyway…
    • Resolved
    • Answered

  • RE: ADS42LB49EVM: Clock input voltage range

    Resolved
    Mahmoud, I would use the CDCE6200EVM with a single-ended LVCMOS output and use an in line attenuator before connecting this to the ADS42LB49EVM. Measure the voltage at the ADC clk input pins to make sure the level is within spec of the ADC. Adjust the…
    • Answered

  • ADS42LB49EVM: 3.3 Voltage rail measuring 2.08 volts

    Resolved
    Part Number: ADS42LB49EVM Hello, The ADC board showing 2.08 volts on the 3.3 volts rail, I am checking the two sides of unfitted F2. The input side shows 3.37 as expected but the output side is showing 2.08 and therefore all supply lines are now…
    • Resolved
    • Answered

  • ADS42LB49EVM: Sine wave test pattern does not match the one on datasheet

    Resolved
    Part Number: ADS42LB49EVM Other Parts Discussed in Thread: ADS42LB49 Hello, I am using ADS42LB49EVM Rev B and the generated 8 points sine wave is: 0 5792 8191 5792 0 -5793 -8192 -5793 This does not match the values on the datasheet, could you…
    • Resolved
    • Answered

  • RE: HSMC-ADC-Bridge/ADS42LB49EVM compatibility

    Resolved
    Patrick, I will look into this for you. Did you order the HSMC-ADC-BRIDGE card? When you mention "Does not work" can you tell me what the issue was? Regards, Jim

  • RE: ADS42LB49EVM syncing

    Hi Rafal, The ADCs can still be synchronized just that the sync enable bit no longer exists or is required to synchronize the ADCs. Thanks, Eben.

  • ADS42LB69EVM: TIMED_OUT_ERROR

    Part Number: ADS42LB69EVM Other Parts Discussed in Thread: ADS42LB49EVM Hello, I have encountered a problem using the TSW1400EVM and the ADS42LB69EVM boards to capture data. Specifically, I followed the instructions to connect them but when I tried to…
    • Answered

  • RE: ADS42B49EVM: Differences between ADS42B49EVM Rev A Rev B

    Resolved
    Thanks for your reply Jim, Sorry I was referring to ADS42LB49EVM not ADS42B49EVM Does the same still applies to ADSLB49EVM? I purchased two boards from a known supplier and I received Rev A and B Regards, Mahmoud

Didn't find what you are looking for? Post a new question.