Search tips
Showing 49 results View by: Thread Post Sort by

  • ADS52J65: VCM , Analog input FS

    Part Number: ADS52J65 Tool/software: Dear TI team I have some question about the Analog input in ADS52J65 In the datasheet file Page 29 “For a full-scale differential input, each input pin INP, INM must swing symmetrically between VCM + 0.5…
    • Answered

  • ADS52J65: ADC RF input impedance question

    Resolved
    Part Number: ADS52J65 Tool/software: Hello, I'd like to inquire about the RF input port of the ADS52J65. I've thoroughly reviewed the data sheets provided by TI, but I couldn't find any information regarding the impedance of the RF input port.…
    • Resolved

  • ADS52J65: FDA Driver

    Part Number: ADS52J65 Other Parts Discussed in Thread: LMH6553 , Hi, I am in the process of developing an ADC PCB. I intend to use the ADS52J65 ADC, for which I have already performed initial tests with your evaluation board to verify the basic functions…

  • ADS52J65: Logic level of ADS52J65 SYNC ? How to properly drive SYNC pins via FPGA IOs?

    TI Thinks Resolved
    Part Number: ADS52J65 Team, Can you please help with the below? The ADS52J65 is supplied with 1V15. -What is the proper way to drive the ADS52J65 SYNC pins? We want to drive it differentially with 1V8 LVDS IO from an Xilink Ultrascale. -How should the Xilinx…
    • Answered

  • ADS52J65: Can TI-JESD204-IP be used for FPGA design to interface to ADS52J65?

    Resolved
    Part Number: ADS52J65 Team, I don't see the ADS52J65 being listed in the "Supported products & hardware" at: https://www.ti.com/tool/TI-JESD204-IP#downloads Can you please confirm if ADS52J65 is supported? If not what would be the needed…
    • Resolved
    • Answered

  • ADS52J65: ADS52J65: Which JESD204B signals require length matching?

    Resolved
    Part Number: ADS52J65 I realize the question has been asked before but reading the various blogs and ADS52J65 datasheet, I just want to confirm that my understanding is correct regarding trace length matching in my particular setup, which matches the…
    • Resolved

  • ADS52J65EVM: Can not select ADS52J65 in DATACONVERTERPRO-SW GUI drop-down menu

    Part Number: ADS52J65EVM Other Parts Discussed in Thread: ADS52J65 , DATACONVERTERPRO-SW , TSW14J50EVM Hi Team, My customer can't find ADS52J65 (EVM) in the drop-down menu of DATACONVERTERPRO-SW GUI drop-down menu to work with it in conjunction with TSW14J50EVM…
    • Answered

  • ADS52J65: Differential Input Resistance and Capacitance?

    Resolved
    Part Number: ADS52J65 Other Parts Discussed in Thread: TINA-TI Can you please tell me the input differential resistance and capacitance for this ADS52J65 ADC? I need to set up a Bessel filter at the input, so I need to know what the input looks like. Thank…
    • Resolved

  • ADS52J65: Decimation block bypass setting

    Part Number: ADS52J65 Hello, In order to bypass the decimation block and directly receive the ADC output, are there any registers that need to be controlled in addition to the decimation block disable bit? Thank you. JH

  • RE: ADS52J65: DEMOD 3-wire mode MISC 0x2E

    Hi Hiroto-san, I am closing this thread as well. The 3Wire SPI (demod) is not supported in ADS52J65 Regards, Abhishek

Didn't find what you are looking for? Post a new question.