Search tips
Showing 18 results View by: Thread Post Sort by

  • RE: ADS6142-HT: ADS6142-HT vs ADS6142

    Katie, Are you looking at the latest data sheet? The one attached does not list 85C but a range from -40 to 125 and the two current numbers are 0.76mA and 0.75mA. See attached. Regards, Jim ads6142-ht.pdf

  • ADS6142: When the temperature of ads6142 is too high (about higher than 50 degrees), the output has noise.

    TI Thinks Resolved
    Part Number: ADS6142 Problem Description: After the temperature of the thermal imager test chip rises by 50 degrees, the input is 0, and the output has noise and serious interference. The output waveform is shown in the attached picture. After the temperature…

  • ADS6142: ADS6142温度过高后（大约高于50度）后输出有噪声

    TI Thinks Resolved
    Part Number: ADS6142 问题描述： 热成像仪测试芯片温度升高50度后，输入为0，输出有噪声， 干扰严重，输出波形如附件图片。温度降低后，输出噪声消失，输出波形特别干净。麻烦帮忙分析下。 PCB说明： 电路板的模拟地和数字地没有单点接地，两个地共用，原理图及部分PCB图片见附件， 对于PCB layout 有没有好的建议，也可以提供下。谢谢！ ADS6142_原理图.pdf

  • ADS6142-HT: replacement to AD7981HFZ

    TI Thinks Resolved
    Part Number: ADS6142-HT Hello, Do we have a replacement to the following device? AD7981HFZ Thanks in advance, Best Regards, Needhu
    • Answered

  • ADS6142: ADS6142:ECCN

    Resolved
    Part Number: ADS6142 Hello, I'm looking for ECCN - Classification of ADS6142. Thank you! BR
    • Resolved

  • ADS6142EVM: USB driver for USB to SPI chip on ADS6142 EVB

    Part Number: ADS6142EVM Which driver do I use for the FTDI device on the ADC eval boards used to talk to TI ADC SPI 5p1 GUI ? Can I get a link to the download?
    • Answered

  • ADS6142: about power supply sequence

    Resolved
    Part Number: ADS6142 Hi, Does this device have power supply start-up and shut-down regulations? Customer is considering startup and shutdown sequences and time rules. Could you give me your advice? Best Regards, Yusuke/Japan Disty
    • Resolved
    • Answered

  • ADS6142: Resister values on the analog inputs

    Resolved
    Part Number: ADS6142 Hi Team, Please advise me on questions bellow. The figure 98 on the ADS6142 datasheet illustrates application circuit. Q1. Two 200 ohm resisters are used as the VCM bias circuit. Can they be substitute with two 220 ohm resisters or…
    • Resolved

  • RE: ADS6142: PDN pin processing in serial control condition

    Hi, i have had not been able to get any further information regarding the PDN pin of this device beyond what is in the datasheet. While in serial configuration I would say that it would be safest to leave the PDN pin low. Regards, Richard P.
    • Answered

  • ADS6142: about Default value of the register

    Resolved
    Part Number: ADS6142 Hi, Could you tell me default value of SERIAL REGISTER? It was not listed in a datasheet. Best Regards, Yusuke/Japan Disty
    • Resolved

Didn't find what you are looking for? Post a new question.