Search tips
Showing 24 results View by: Thread Post Sort by

  • ADS62P42: Is there a single channel version of ADS62P42 ?

    TI Thinks Resolved
    Part Number: ADS62P42 Other Parts Discussed in Thread: ADC3664 Tool/software: Have tried searching but have failed to find an alternative. What I really want is 12 - 14 bits (could live with more) 50 - 100 Msps Built in programmable FIR filter…

  • ADS62P42: ADS62P42 could not keeping SPI setting of CMOS MUX mode long time ?

    Part Number: ADS62P42 As described in the subject I'm using the ADS62P42 in CMOS MUX Mode. I have to mention that all 3 parallel control pins are at GND to have serial (SPI) config only and that I put in register 14 the power down mode at 111 (MUX mode…

  • RE: ADS62P42: Is there a pin compatible part that can do 160MSPS or higher?

    Hi Victor, I do not believe that there is a pin to pin compatible device that fits your requirements. Best Regards, Dan
    • Answered

  • ads62p42 SPI control

    Resolved
    Other Parts Discussed in Thread: ADS62P42 Hello, I have the ADS62P42EVM REV E. board and I've connected TP10, TP11, TP13 (SCLK, SDATA,SEN) to an external controller that provide SPI signals according to the timing diagram in the data sheet. in addtion…
    • Resolved

  • ADS62P42 CMOS MUX mode only deliver B input...receive garbage for input A

    Other Parts Discussed in Thread: ADS62P42 , DAC5672 As described in the subject I'm using the ADS62P42 in CMOS MUX Mode and I'm receiving the result for Input B and I'm getting garbage near noise for input A. If I switch I and Q I can really see that…
    • Answered

  • Interfacing C28346 with ADS62P42.

    Resolved
    Other Parts Discussed in Thread: ADS7865 , ADS62P42 Hi all, I'm trying connect an ADC to c28346 ( I use C28346 DIM168 ControlCARD ). The ADC is ADS62P42 , it has 2 channels 14bits each, up to 65MSPS and a parallel interface. I'm using an example…
    • Resolved

  • How to use parallel interface of ADS62P42.

    Other Parts Discussed in Thread: ADS62P42 Hi! What would be the best way to connect ADS62P42 and a microcontroller ( C28346 ) ? thanks, Janek
    • Answered

  • Example schematic for ADS62P42 and TRF371125 connection

    Resolved
    Other Parts Discussed in Thread: TRF371125 , ADS62P42 , ADS5282 Can you provide detail example schematic for ADS62P42 and TRF371125 connection. system request: 1. I/Q Frequency response: 0~30MHz 2. Low DC offset 3. Low noise floor 4. I…
    • Resolved
    • Answered

  • ads62p4x

    Resolved
    Other Parts Discussed in Thread: ADS62P42 , LMH6518 , THS4509 , LMH6521 Hi, I'm trying to interface ADS62p42 with a low pass differential amp, but I noticed from the data sheet, Figure 86, that the two termination resistors, <100 ohms has to be tied to…
    • Resolved

  • RE: offset of ADS62P42IRGCT

    Hi Hongping, The ADS62P42 datasheet lists the min and max offset error as +/- 10 mV. This is a 14-bit part with a 2-Vpp input voltage. The step size is about 122 uV, so the min and max offset error should be +/- 82 LSBs. So it sounds like you are outside…

Didn't find what you are looking for? Post a new question.