• ADS7852: ADS7852

  

  Rajashekhar Reddy

  TI Thinks Resolved

  Part Number: ADS7852 Tool/software: Hi, For ADS7852, what is clock min and max level, I am planning to to 8MHz TCXO, its max VOH is 2.6V. If i use this clock (VOH is 2.6), will the device work in properly? Thanks, RR

  • 2 months ago
  • Data converters
  • Data converters forum
Answered

• ADS7852: ADS7852 IBIS

  

  ?? ??

  Resolved

  Part Number: ADS7852 Other Parts Discussed in Thread: ADS8365 , Tool/software: Hi, TI E2E. In order to conduct simulation of the transmission line on the circuit board, is it possible to obtain the IBIS model for the following components? If unavailable…

  • Resolved

  • 2 months ago
  • Data converters
  • Data converters forum
Answered

• ADS7852: Date code confirmation request from top marking (SO 331633)

  

  Dan Lee

  Resolved

  Part Number: ADS7852 Tool/software: Hello Tech Support Team, The customer would like to confirm the date code of part#ADS7852YB/250 they received. Could you please check the top marking and advise on the correct date code? Thanks. Best Regards, Dan…

  • Resolved

  • 4 months ago
  • Data converters
  • Data converters forum

• ADS7852: Recovering from power glitch

  

  Kim Martinsen

  Part Number: ADS7852 Hi, I'm having problems with the ADS7852 going into some latched up mode. If a glitch in the 5V power supply, that resets the main processor while it is setting the ADC to a new channel, the ADC keeps the BUSY signal low. After…

  • over 1 year ago
  • Data converters
  • Data converters forum
Answered

• ADS7852: Timing clarification for BUSY pin

  

  Iain Macalister

  Resolved

  Part Number: ADS7852 The datasheet states "the ¬BUSY output will go LOW approximately 20ns after the falling edge of the ¬WR pin". The Figure 2 timing diagram specifies that ¬BUSY will go low at least 20 ns after ¬CS goes low.…

  • Resolved

  • over 1 year ago
  • Data converters
  • Data converters forum
Answered

• ADS7852: Request IBIS model

  

  Akihisa Tamazaki

  Resolved

  Part Number: ADS7852 Hello team, The customer requested an IBIS model for the ADS7852 ? If not, is there an IBIS model for a similar product? Best Regards, Akihisa Tamazaki

  • Resolved

  • over 2 years ago
  • Data converters
  • Data converters forum

• ADS7852: Read operation

  

  Takeshi Sasaki

  TI Thinks Resolved

  Part Number: ADS7852 Hi team, Could you give me comment on following customer question? Q1. Can the customer use ADS7852 for the read operation as 2 times? Or Is it have any potential issues? As seeing previous e2e thread as below, ADS7852 operates one…

  • over 4 years ago
  • Data converters
  • Data converters forum

• ADS7852: BUSY signal output specifications

  

  user802427

  TI Thinks Resolved

  Part Number: ADS7852 In order to receive BUSY signal output by LVTTL, voltage is converted by connecting 2.4K ohm and 4.7k ohm to GND. Is the output voltage in this case received in the range of 2v to 3.3v?

  • over 5 years ago
  • Data converters
  • Data converters forum

• ADS7852: can I ground the /CS input?

  

  mike leggett

  TI Thinks Resolved

  Part Number: ADS7852 If I do not want to utilize the power down features, can I ground the /CS input? Note: email address was Michael.leggett@cobham.com changed to Michael.leggett@cobhamaes.com

  • over 4 years ago
  • Data converters
  • Data converters forum

• ADS7852: About internal ESD protection diode

  

  Hide

  TI Thinks Resolved

  Part Number: ADS7852 Hi Team, Does ADS7852YB have the internal ESD protection diode? I guess that Analog/Digital inputs and REFIN pin have internal diode for VCC and GND, +VSS have internal diode for GND only. Because, " ABSOLUTE MAXIMUM RATINGS " shows…

  • over 5 years ago
  • Data converters
  • Data converters forum

Didn't find what you are looking for? Post a new question.