TI E2E support forums
TI E2E support forums
  • User
  • Site
  • Search
  • User
  • E2E™ design support >
  • Forums
    • Amplifiers
    • API solutions
    • Audio
    • Clock & timing
    • Data converters
    • DLP® products
    • Interface
    • Isolation
    • Logic
    • Microcontrollers
    • Motor drivers
    • Power management
    • Processors
    • RF & microwave
    • Sensors
    • Site support
    • Switches & multiplexers
    • Tools
    • Wireless connectivity
    • Archived forums
    • Archived groups
  • Technical articles
  • TI training
    • Tech days
    • Online training
    • Live events
    • Power Supply Design Seminar
  • Getting started
  • 简体中文
  • More
  • Cancel


Search tips
Showing 10 results View by: Thread Post Sort by
  • AMC1106M05: Offset is higher then specified in datasheet.

    Peter Nicolai
    Peter Nicolai
    Part Number: AMC1106M05 Hi, We are using the AMC1106M05, The maximum offset should be 50uV according to the datasheet. In some cases the offset is higher then this specification. The temperature of the board is stable at 22'C. Both inputs are shorted to…
    • over 1 year ago
    • Data converters
    • Data converters forum
  • Answered
  • RE: AMC1106M05: several question for AMC1106M05

    Tom Hendrick
    Tom Hendrick
    Resolved
    Sure, From the datasheet: "The AMC1106 incorporates front-end circuitry that contains a differential amplifier and sampling stage, followed by a ΔΣ modulator. The gain of the differential amplifier is set by internal precision resistors to a factor of…
    • over 2 years ago
    • Data converters
    • Data converters forum
  • Answered
  • AMC1106M05: Data timing related to modulator clock

    Michael Kettler
    Michael Kettler
    Resolved
    Part Number: AMC1106M05 Other Parts Discussed in Thread: TMS320F28388D , Hello, I am struggling with the signal timing of the AMC1106M05 delta sigma modulator, together with the TMS320F28388D. In principle what I have is this: The timing diagramm will…
    • Resolved
    • over 2 years ago
    • Data converters
    • Data converters forum
  • Answered
  • AMC1106M05: configuration of shunt resistor

    Josef Warta
    Josef Warta
    Resolved
    Part Number: AMC1106M05 Hello Team, my customer needs support on shunt resistor configuration Target is to achieve a measurement range of +/-350A-p (referred to +/-64mV). Shunt selection is difficult because only certain standard values are available…
    • Resolved
    • over 3 years ago
    • Data converters
    • Data converters forum
  • Answered
  • AMC1106M05: acceptable voltage on input pins

    Zahra Derafshi
    Zahra Derafshi
    Resolved
    Part Number: AMC1106M05 Hi, I'm looking at the datasheet for AMC1106x and in the typical application section it shows that the shunt resistors can be connected to the hot lines. Also in the datasheet mentions that the voltage that can be on input…
    • Resolved
    • over 3 years ago
    • Data converters
    • Data converters forum
  • AMC1106M05: What is the Data format from DOUT?

    John Liu33
    John Liu33
    Part Number: AMC1106M05 I try to use AMC1106M05 in my design. I read though the datasheet. But I still do not know what is format of data? How do I know the start of a data, or end? How many bits of the data from DOUT? If any info, will be greatly appreciated…
    • over 6 years ago
    • Data converters
    • Data converters forum
  • RE: AMC1106E05: AMC1106 High Current Reading at Startup

    Tom Hendrick
    Tom Hendrick
    Hi Utku, Can I ask you how much of the TIDA-01094 reference design you are using? The AMC1106M05 itself should not be causing the problem, but you can try to verify that by removing the diodes and make sure that AGND is tied back to your shunt. I was…
    • over 2 years ago
    • Data converters
    • Data converters forum
  • Answered
  • TIDA-01063: Sensing current range of PCB Rogowski sensor

    Linda Chen
    Linda Chen
    Resolved
    Part Number: TIDA-01063 Other Parts Discussed in Thread: TIDM-3PHMETER-ROGOWSKI , TMCS1100 , AMC3301 , AMC1106M05 , Dear TI expert, I am finding a low cost sensor to measure a low current for overlaod protection, current range from 0.16A to 5A, 50/60Hz. I would…
    • Resolved
    • over 5 years ago
    • Simulation, hardware & system design tools
    • Simulation, hardware & system design tools forum
  • Answered
  • RE: Looking for references for isolated line voltage measurements and zero crossing detection

    Tom Hendrick
    Tom Hendrick
    Resolved
    Hi Cody! One of my associates is suggesting that you might take a look into the AMC1106M05. This could provide Option 3 if you have the means to filter a digital bit stream similar to what was done with our TIDA-01639 reference design. Take a look and…
    • over 5 years ago
    • Isolation
    • Isolation forum
  • Answered
  • TMS320F280049: ADC synchronization with SDFM

    Dmitry Sharihin
    Dmitry Sharihin
    Resolved
    Part Number: TMS320F280049 Other Parts Discussed in Thread: AMC1106M05 , AMC1106E05 Hello, I want to perform current measurement with SDFM module and AMC1106M05 while measure voltage with internal ADC. For accurate result acquisition I need to get almost…
    • Resolved
    • over 6 years ago
    • C2000™︎ microcontrollers
    • C2000 microcontrollers forum

Didn't find what you are looking for? Post a new question.

  • Ask a new question