Search tips
Showing 89 results View by: Thread Post Sort by

  • AWR2544LOPEVM: AWR2544LOPEVM: Question about LoP Size

    TI Thinks Resolved
    Part Number: AWR2544LOPEVM Tool/software: Hi, I'm planning to deisgn waveguide antenna. What I see in your document showed that LoP has been doing sieze reduction From 4x6 to 4x5 solder balls In your Encrypt model(4x6 solder balls) has Waveport size …

  • AWR2544LOPEVM: AWR2544LOPEVM: The 1000Base-T1 AUTO PHY(DP83TG720) on the EVB to 100Base-T1 AUTO PHY(DP83TC812)

    Part Number: AWR2544LOPEVM Other Parts Discussed in Thread: AWR2544 , SYSCONFIG , , DP83TG720EVM-MC Tool/software: Hi, I need help to enable DP83TC812 for AWR2544. Currently I got a new task for the AWR2544, switch the auto phy from 1000Base-T1 DP83TG720…
    • Answered

  • AWR2544LOPEVM: AWR2544LOPEVM - Tx phase shifters in mmWave Studio

    Resolved
    Part Number: AWR2544LOPEVM Other Parts Discussed in Thread: AWR2544 Tool/software: Hi everyone, I am working on the AWR2544LOPEVM eval board with DCA1000 for data acquisition, which works well with FMCW/TDMA MIMO. This works well so far. Now I would…
    • Resolved

  • AWR2544LOPEVM: Zeros (0x00) appearing inside Ethernet payload data – how to resolve?

    Part Number: AWR2544LOPEVM Tool/software: Hello, I am using the AWR2544LOPEVM to stream radar cube data over Ethernet. When I capture the data using ROS, I observe that long sequences of 0x00 values appear in the middle of the payload . My current…

  • AWR2544LOPEVM: Debuger error problem

    Part Number: AWR2544LOPEVM Tool/software: Hello! I'm new using AWR2544LOPEVM board and I'm trying to use ccs debuger. I tried using TI example codes like hello world and mmw out of box code but i get error message that one file cannot found(picture…

  • AWR2544LOPEVM: CSI2 Packetization Configurations

    TI Thinks Resolved
    Part Number: AWR2544LOPEVM Other Parts Discussed in Thread: AWR2544 Tool/software: Hi, I am developing CSI2 driver on awr2544 to enable streaming raw ADC data via CSI2-TX. From the other end, I'm using CSI2-RX of TMDS273x to receive that raw ADC data…
    • Answered

  • AWR2544LOPEVM: RADAR INTERFACE ERROR MSS Power Up async event was not received!

    Resolved
    Part Number: AWR2544LOPEVM Other Parts Discussed in Thread: AWR2544 Tool/software: Hi, I am connecting the AWR2544LOPEVM to the DCA1000 (setup as shown in Figure 1), and when attempting SPI connect I encountered the issue shown in Figure 2. What solutions…
    • Resolved

  • AWR2544LOPEVM: AWR2544LOPEVM can not recognize by PC

    TI Thinks Resolved
    Part Number: AWR2544LOPEVM Other Parts Discussed in Thread: AWR2944 Tool/software: Dears, USB port (XDS_USB) Connect the USB cable to the computer, and an error message will be displayed after power-on. The USB cable also comes with the development…

  • AWR2544LOPEVM: How to enable ContStream feature on mmwavestudio for awr2544

    TI Thinks Resolved
    Part Number: AWR2544LOPEVM Other Parts Discussed in Thread: AWR2544 , DCA1000EVM Tool/software: Hi team, i have a set up with awr2544evm and dca1000. I’m able to use this setup with mmwavestudio with no issue. However, im trying to run this with continuous…

  • AWR2544LOPEVM: 12-bit Data Streaming via mmWave Studio

    TI Thinks Resolved
    Part Number: AWR2544LOPEVM Other Parts Discussed in Thread: AWR2544 Tool/software: Hi, I’m using mmWave Studio to connect the EVM to the DCA and save data to my computer over Ethernet. On the DCA, I see options for 12/14/16-bit data output. I need…

Didn't find what you are looking for? Post a new question.