• 

  Yanming Luo

  • 3 months ago
  • Motor drivers
  • Motor drivers forum

  RE: BOOSTXL-DRV8301: Question about inductance identification

  I don't think there are more other reasons if you follow the instructions in the lab guide to tuning the identification parameters I mentioned above. You have to check the hardware board and make sure that the ADC, WPM, and GPIO configurations are...
• 

  F.F

  • 5 months ago
  • Motor drivers
  • Motor drivers forum

  BOOSTXL-DRV8301: How to calculate the USER_MOTOR_MAX_CURRENT value

  • Resolved

  Part Number: BOOSTXL - DRV8301 Dear Yanming: In instaSPIN, how can I get the value
• 

  F.F

  • 5 months ago
  • Motor drivers
  • Motor drivers forum

  BOOSTXL-DRV8301: The actual current is much less than Id_ ref

  • Resolved

  Part Number: BOOSTXL - DRV8301 Dear Yanming: My clients refer to the board designed by boost xl
• 

  Yanming Luo

  • 4 months ago
  • Motor drivers
  • Motor drivers forum

  RE: CCS/BOOSTXL-DRV8301: Hard to identify motor - high inertia

  Understand. You might try to tune the parameters to identify again. If still failed, you have to ask the motor manufacturer to get the motor parameters and refer to chapter 6.8 of the user's guide to set the motor parameters. InstaSPIN-FOC and InstaSPIN...
• 

  Matt Koerner

  • 5 months ago
  • Motor drivers
  • Motor drivers forum

  RE: BOOSTXL-DRV8301: InstaSPIN software gives error when signing in.

  I tried a third board we had and that seems to have resolved the issue. Thank you everybody for your help. Matt
• 

  Marcos M

  • 11 months ago
  • Motor drivers
  • Motor drivers forum

  BOOSTXL-DRV8301: BOOSTXL-DRV8301

  • Resolved

  Part Number: BOOSTXL - DRV8301 Hello everyone. I've got a question on a BOOSTXL - DRV8301 users. As far
• 

  David Kyle1

  • 7 months ago
  • C2000™ microcontrollers
  • C2000™ microcontrollers forum

  RE: CCS/BOOSTXL-DRV8301: Code Composer Studio™ forum

  Thanks for clarifying that, Yanming. Best Regards, Dave Kyle
• 

  Yanming Luo

  • 7 months ago
  • Code Composer Studio™
  • Code Composer Studio™ forum

  RE: CCS/BOOSTXL-DRV8301: User_ErrorCode_voltageFilterPole_Hz_Low

  Change the C34/C35/C36 (01.uF) to a small capacitance, and refer to section 5.2.4 of InstaSPIN User's Guide (SPRUHJ1H) to calculate the filter pole. http://www.ti.com/lit/ug/spruhj1h/spruhj1h.pdf
• 

  Aaron Barrera

  • 7 months ago
  • Motor drivers
  • Motor drivers forum

  RE: BOOSTXL-DRV8301: Not getting proper Gate pulses for MOSFETs

  HI Abdul, Your measurements seem fine, but can you confirm by measuring your GHx signals with respect to SHx? You should be able to see them cycle on and off at around 10V rather than VM + 10V.
• 

  Yash Gokhale

  • 8 months ago
  • Code Composer Studio™
  • Code Composer Studio™ forum

  RE: CCS/BOOSTXL-DRV8301: INSTASPIN UNIVERSAL GUI : MOTOR IS NOT IDENTIFIED AND DIRECTLY MOTOR STARTS TO VIBRATE AS SOON AS SYSTEM IS ENABLED AND RAN

  Hello I resolved the issue... I tried lab2c to sense the parameters and was able to run the motor by tuning PID parameters in lab5b and running program in debug mode. Regards Yash

Didn't find what you are looking for? Post a new question.

• Ask a new question