Search tips
Showing 92 results View by: Thread Post Sort by
    Answered

  • BQ25600D: Why do SCL and SDA keep same state?

    Resolved
    Part Number: BQ25600D Other Parts Discussed in Thread: BQ25600 Hi team, MCU send reset signal to BQ25600D through I2C, then reset is turned on. However SCL and SDA don't start to operate. Can you estimate why the signal don't operate? If this situation…
    • Resolved
    • Answered

  • BQ25600D: 2 states can be observed although I tested similar situation

    Resolved
    Part Number: BQ25600D Hi team, When the load is changed during low voltage battery, we can observe 2 states like below (VBUS is unconnected). Could you estimate why 2 states can be observed although similar situation? Pink shows Vsys waveform and…
    • Resolved

  • BQ25600D: BQ25600D About VBAT_UVLOZ : I2C actvive Hysteresis Spec

    TI Thinks Resolved
    Part Number: BQ25600D Hi I have one question for BQ25600D . My question is I2C active hysteresis spec . This device has V VAC_UVLOZ with I2C active hysteresis spec * Data Sheet Page 8,9 . But VBAT_UVLOZ dose not have I2C active hysteresis spec…

  • BQ25600D: charger IC FW setting

    TI Thinks Resolved
    Part Number: BQ25600D Hi, charger IC , BQ2500D is using I2C I/F can it set charger with a suspend mode , that no draw any current from USB input side ? any document about the FW setting ? thanks. joseph.
    • Answered

  • [FAQ] BQ25601: [FAQ] Could TI provide the sample Linux driver for the BQ25618, BQ25618E, BQ25619, BQ25611D, BQ25600, BQ25600D, BQ25601, BQ25601D?

    Resolved
    Part Number: BQ25601 Other Parts Discussed in Thread: BQ25619 , BQ25600 , , , BQ25600D , BQ25618E , BQ25618 , BQ25611D The sample Linux driver for BQ25618, BQ25618E, BQ25619, BQ25611D, BQ25600, BQ25600D, BQ25601, BQ25601D is located here: www.ti.com…
    • Resolved
    • Answered

  • BQ25600D: NTC fault report

    Resolved
    Part Number: BQ25600D Other Parts Discussed in Thread: BQSTUDIO , BQ25898 Hi, I know that bq25600D has INT output but it does not generate INT pulse at NTC fault event. Is my understanding correct? Then does the customer need to poll REG09[2:0] bit…
    • Resolved

  • BQ25600D: Recommended NTC thermistor

    TI Thinks Resolved
    Part Number: BQ25600D Hi, I know that the recommended NTC thermistor is 103AT-2 that is listed in datasheet. But now the customer would like to use 100kohm NTC with B=4250 . Can you recommend to use this NTC thermistor? Please tell me the external…
    • Answered

  • BQ25600D: About D+/D– detection

    Resolved
    Part Number: BQ25600D Hi, Could you tell me about TPS25600D D+/D- detection? Customers want to force D+/D- Detection events. Is it possible to realize using Bit of IINDET_EN? Detection starts when this bit is set, and it is automatically cleared when…
    • Resolved
    • Answered

  • BQ25600D: BQ25600

    Resolved
    Part Number: BQ25600D Other Parts Discussed in Thread: BQ25600 , BQ25601 , BQ25895 Hi, We are planning to use BQ25600 PMIC in one of our battery operated vibration sensor . we are in doubt about vibration acceptance of BGA package of BQ25600, (…
    • Resolved
    • Answered

  • BQ25600D: Input capacitance of SCL and SDA pin

    Resolved
    Part Number: BQ25600D Hi, Please let me ask the input capacitance of SCL and SDA pin of bq25600D. I don't need guaranteed value so rough typical value should be enough. Best Regards, Satoshi
    • Resolved

Didn't find what you are looking for? Post a new question.