TI E2E support forums
TI E2E support forums
  • User
  • Site
  • Search
  • User
  • E2E™ design support >
  • Forums
    • Amplifiers
    • API solutions
    • Audio
    • Clock & timing
    • Data converters
    • DLP® products
    • Interface
    • Isolation
    • Logic
    • Microcontrollers
    • Motor drivers
    • Power management
    • Processors
    • RF & microwave
    • Sensors
    • Site support
    • Switches & multiplexers
    • Tools
    • Wireless connectivity
    • Archived forums
    • Archived groups
  • Technical articles
  • TI training
    • Tech days
    • Online training
    • Live events
    • Power Supply Design Seminar
  • Getting started
  • 简体中文
  • More
  • Cancel


Search tips
Showing 71 results View by: Thread Post Sort by
    Answered
  • BQ25758: BQ25758 L1 value issue

    ?? ?
    ?? ?
    Resolved
    Part Number: BQ25758 Tool/software: HI Sir, BQ25758 pass inductor L1 "Table 7-1. Recommended Part Numbers for up-to 48-V EPR (5-A output): (continued)" show CMLB135T-100MS value: 10 μH, 22 mΩ, 10.5~13A if i use 19.5V/15A input, is…
    • Resolved
    • 6 days ago
    • Power management
    • Power management forum
  • RE: BQ25758: Current Sensing Problems

    Michael Bradbourne
    Michael Bradbourne
    Hey Quinn, Just following up with this thread. Has the external supply helped fix the issue? Since there has not been much activity on the thread in a while, it may become closed soon. If you have any further questions, you can always start a new thread…
    • 9 days ago
    • Power management
    • Power management forum
  • RE: BQ25758: Can BQ25758 be controlled by TPS25751's I2C?

    Raymond Lin
    Raymond Lin
    Hi Yamazaki-san, Hiroaki Yamazaki said: In fact, I don't need a complete PPS. I just need to switch between 5V3A and 15V3A. Is it possible to prepare these two power supplies, input them to the PPHV and PP5V of the TPS25751, and switch the voltage by turning…
    • 3 months ago
    • Power management
    • Power management forum
  • BQ25758: Startup Behavior and Gate Drive Control

    Carissa Pocock
    Carissa Pocock
    Part Number: BQ25758 Other Parts Discussed in Thread: BQ25756 Tool/software: Hello- I am interested in understanding more about the start-up behavior of this charger, and the gate drive timing limitations. Gate Drive: What is the minimum controllable ON…
    • 1 month ago
    • Power management
    • Power management forum
  • Answered
  • RE: BQ25758S: BQ25758S as Buck Boost only

    Ethan Galloway
    Ethan Galloway
    Resolved
    Hello Muhammad, Muhammad Awais said: Should I assume that we are going to use it in Buck-Only as our output will always be at 5V? Buck-only mode would make sense for your application. Muhammad Awais said: If yes then what about the case when we only need…
    • 5 months ago
    • Power management
    • Power management forum
  • RE: BQ25758: BQ25758 OCP Notification via INT pin

    Ethan Galloway
    Ethan Galloway
    Hello Sudheer, The BQ25758 will go back to CC mode once the output load current is reduced below IOUT_REG. At this moment, VOUT_Measured=VOUT_REG and the BQ25758 will go back into CV mode. Let me know if you have any questions about this. Best Regards…
    • 5 months ago
    • Power management
    • Power management forum
  • BQ25758: BQ25758: Discharge to 5 V from higher Voltages

    Sudheer Gaddipati
    Sudheer Gaddipati
    TI Thinks Resolved
    Part Number: BQ25758 Tool/software: Hi Team, Recently we are testing BQ25758 and found out that, it takes sometime for BQ25758 to ramp down from 48V to 5V. We do have external discharge circuitry and when it is enabled VBUS on type-c connector discharge…
    • 5 months ago
    • Power management
    • Power management forum
  • TPS26750: Compatibility with the BQ25758

    Santiago Allen
    Santiago Allen
    TI Thinks Resolved
    Part Number: TPS26750 Other Parts Discussed in Thread: BQ25756EVM , BQ25758 , BQ25756 Tool/software: Hi TI Team, I am looking into a USB C PD setup, and I found some components that I believe to be compatible but could use some advice on. From what I am…
    • 2 months ago
    • Power management
    • Power management forum
  • BQ25758: BQ25758 and BQ25756

    Roy Lin1
    Roy Lin1
    TI Thinks Resolved
    Part Number: BQ25758 Other Parts Discussed in Thread: BQ25756 , Tool/software: Hi team, Customer ask what is the difference between BQ25756 and BQ25758, Can you show the key differences of these two devices? Is BQ25758 only can work with 14 cells battery…
    • 6 months ago
    • Power management
    • Power management forum
  • Answered
  • BQ25758: Can Two MOSFET with BQ25758 support bidirectional converter ?

    Ken Zhang
    Ken Zhang
    Resolved
    Part Number: BQ25758 Tool/software: hi, A my account needs a bidirectional converter with below spec. Can BQ25758 setting in buck-only mode(only two MOSFETs(Q1 & Q2) are used) support reverse mode? Forward way: From input to output; input voltage…
    • Resolved
    • 5 months ago
    • Power management
    • Power management forum
>

Didn't find what you are looking for? Post a new question.

  • Ask a new question