Search tips
Showing 59 results View by: Thread Post Sort by

  • BQ27510EVM: I can't read the SOC register properly.

    TI Thinks Resolved
    Part Number: BQ27510EVM Other Parts Discussed in Thread: BQ27510 , EV2400 , BQSTUDIO I'm having difficulty reading from the bq27510. I know the part is working properly because it reads the correct state of charge when I plug in the EV2400. I'm attempting…

  • RE: BQ27510EVM: Learning cycle fails (update status always 0)

    Hello Khaled, Since bq27510-G3 is a system side gauge, you have completed learning when Update status = 0x02 There are jumps in load in both logs, this can sometimes result in failure to learn. I will also recommend that you use a good charger because…

  • BQ27510EVM: Learning cycle fails (QEN bit always low )

    Part Number: BQ27510EVM Other Parts Discussed in Thread: BQ27510 , BQSTUDIO Dear All, I tried to operate the learning cycle for bq27510 using the bq27510EVM and bqstudio, I followed these steps: Send IT_ENABLE cmd. Send RESET cmd. NOTE: the QEN bit in…

  • BQ27510EVM: Use of EV2300 with BQ27510EVM

    TI Thinks Resolved
    Part Number: BQ27510EVM Other Parts Discussed in Thread: BQ27510 , , BQSTUDIO , EV2400 What is the use of Ev2300 Communications transceiver with the Bq27510. I just need to communicate the Cell voltage, Cell SOC . Will I be able to do this without the EV2300…

  • CCS/BQ27510-G3: How to configure the BQ27510-G3 without bq27510evm and EV2300

    TI Thinks Resolved
    Part Number: BQ27510-G3 Other Parts Discussed in Thread: BQ27510 , MSP430G2553 , , BQ27510EVM , BQSTUDIO , EV2400 Tool/software: Code Composer Studio Hello TI team, After designing a prototype with BQ27510-G3 (communicate I2C with msp430g2553) and getting…
    • Answered

  • BQ27510EVM: Data memory and learning cycle

    Resolved
    Part Number: BQ27510EVM Other Parts Discussed in Thread: BQ27510 , I have purchased bq27510 evm and I am trying to perform a learning cycle. When I try to set the initial parameters and write it to the gauge it shows error "value is beyond maximum value…
    • Resolved

  • BQ27510EVM: EV2400 and BQ2750EVM issues

    TI Thinks Resolved
    Part Number: BQ27510EVM Other Parts Discussed in Thread: BQ27510 , BQSTUDIO , EV2400 I'm trying to get the BQ27510 EVM working with my Windows 10 64-bit machine. I have an EV2400 and have it connect to the BQ27510EVM with a battery installed. BQstudio…

  • BQ27510EVM: GPOUT pin not response when Charge Inhibit occurring

    Part Number: BQ27510EVM I got a BQ27510EVM and try to use GPOUT pin to control charger enable. When I heating the external thermistor, the temperature reading is correct. And the [CHG_INH] bit is set high when temperature over 45 degrees Celsius. But the…

  • RE: BQ27421-G1: Debug registers address location and definitions that are not in the datasheet or technical reference but are available through Bqstudio.

    Shirish, I have obtained the BQ27510EVM and connected our battery and the EV2400. Under Chemistry of BQStudio, I was expecting to be able to program in Chemistry number 5377 that was recommended by the CHEM_ID report for our battery, however I do not…
    • Answered

  • BQ27510-G3: RemCap slightly decreased although AvgCurrent shows still 0 (no load)

    Resolved
    Part Number: BQ27510-G3 Other Parts Discussed in Thread: BQ27510EVM Hi Team, We found RemCap slightly decreased although AvgCurrent always shows 0 (no load) with BQ27510EVM + battery. RemCap decreased about 1mAh in 30 minutes. Is it a possible case for BQ27…
    • Resolved

Didn't find what you are looking for? Post a new question.