Filter by Reset

All
Forums (4,112)
  • Power management (4,058)
  • Simulation, hardware & system... (25)
  • MSP low-power microcontr... (10)
  • Processors (6)
  • Arm-based microcontrolle... (5)
  • Isolation (3)
  • View all
Technical Articles (0)
Wikis (0)
Files (0)
Groups (0)
FAQ
  • Show only FAQs
Reply
  • Resolved
  • TI thinks resolved
  • Answer suggested
  • Has replies by TI employees
  • Has replies
Creation Date
  • Any
  • Past Week
  • Past Month
  • Past 3 Months
  • Past 6 Months
  • Past Year
From
To


Search tips
Showing 4,112 results View by: Thread Post Sort by

  • RE: BQ34Z100-R2: BQ34Z100-R2

    Hello Saran, We are still working on the case and have been working through the queue to get to your question. Your question has been pushed to higher priority Thank you, Alan

  • BQ34Z100-G1: BQ34Z100-G1 pins details (VEN & TS/P6)

    Part Number: BQ34Z100-G1 Tool/software: What are the exact electrical characteristics of pins VEN and P6/TS? I couldn't find sufficiently detailed information in the data sheet. What are electrical properties of VEN? It would be good to know at…

  • BQ34Z100-G1: BQ34Z100-G1

    Part Number: BQ34Z100-G1 Other Parts Discussed in Thread: GPCCHEM Tool/software: Dear All, I get an issu with SOC jump at low temperature. I did a resistance temperature compensation optimization following the sluubd0. I get with the GPC repport the…

  • BQ34Z100-DEVICE-FW: bq34z100

    Part Number: BQ34Z100-DEVICE-FW Other Parts Discussed in Thread: EV2400 Tool/software: I'm downloaded the latest version of the bq studio it is not deducting my fuel gauge ic it showing only none

  • BQ34Z100-G1: Configuring the BQ34Z100 using the EVM2400

    Part Number: BQ34Z100-G1 Other Parts Discussed in Thread: GPCCHEM , BQSTUDIO Tool/software: My FCC and RC are showing 1000mAh, even after several learning cycles, while the TrueRCC and TrueFCC values are reaching 8500mAh. I have set the design capacity…

  • RE: BQ34Z100-R2: BQ34Z100-R2 Learned Status Stuck at 0x4 - FC setting early

    Hi Kris, You FC bit set because you have FC set % = 100, Therefore when SOC reports 100% the FC flag will set. Please change FC set % = -1 until the learning cycle is complete. The gauge will now use Valid charge termination conditions to detect full…

  • RE: BQ34Z100-R2: Inquiry about BQ34Z100-R2 getting hot during operation

    Hi Grady, I reviewed the schematic, and I see no obvious errors. From the schematic and .gg file it appears that this device is being used on a single cell application, typically this device is used with much higher power applications and this problem…

  • BQ34Z100: BQ34Z100 EVM Configuration and Calibration

    Part Number: BQ34Z100 Other Parts Discussed in Thread: BQSTUDIO Tool/software: Hello TI Team, I am trying to connect my BQ34Z100 EVM and modify its configuration values, but I am encountering an issue with the voltage readings. I have set the jumper…

  • RE: BQ34Z100-G1: Configuring the BQ34Z100 using the EVM2400

    Hello Archana, Seems that either the device is not powered up or there is a communication issue with BQStudio. Can you check the voltage on SDA and SCL to make sure the voltages are pulled up. Also, can you check the voltage from REG25. Regards, Adri…

  • BQ34Z100: BQ34Z100 SOC Drop Issue at 100% Rest

    TI Thinks Resolved
    Part Number: BQ34Z100 Tool/software: Dear TI Support Team, We are using the BQ34Z100 for our design and have completed the learning cycle for an 11S1P core pack. We have also conducted charge/discharge and rest tests. Specifically, we performed 12-hour…
1 2 3 4 5 »

Didn't find what you are looking for? Post a new question.