Search tips
Showing 2,860 results View by: Thread Post Sort by

  • BQ34Z100-G1: about RESET command

    Part Number: BQ34Z100-G1 Tool/software: Hi all, All Data Flash values in TRM page 43 Table 7-1 will be Default when resetting by sending RESET command. Is it correct to understand? BQ34Z100-G1 Technical Reference Manual (Rev. A) Best Regards, Ryusu…

  • BQ34Z100-G1: BQ34Z100-G1

    Part Number: BQ34Z100-G1 Other Parts Discussed in Thread: GPCCHEM Tool/software: Volk_Learning_Cycle_2nd.zip Hello, Ti Engineer There is a problem with the Learning Cycle data file I sent you initially, so I will test it again and send it to you. Thank…

  • BQ34Z100-G1: Bq34z100-g1

    TI Thinks Resolved
    Part Number: BQ34Z100-G1 Other Parts Discussed in Thread: SN74HC164 Tool/software: Hello can i work at four led mode with I2C communication? I connected four Leds to p1-p4 and also connected the I2C to host according data sheet page 1. The I2C works but…
    • Answered

  • BQ34Z100: Differences between BQ34Z100, G1, and R2

    Resolved
    Part Number: BQ34Z100 Tool/software: Hi, Please tell me the difference between BQ34Z100, G1, and R2. BQ34Z100 does not support NiMH, Battery capacity 320Ah, does not support SHA-1 Authentication BQ34Z100-R2 supports NiMH, Battery capacity 320Ah, SHA-1…
    • Resolved

  • BQ34Z100-G1: When the small system load below the deadband continues to flow

    Part Number: BQ34Z100-G1 Tool/software: Hi all, What happens to BQ34Z100-G1 if a small system load below the deadband continues to flow? Is it possible to calculate and update SoC etc? If it is not possible to update, if it is left for a long period…

  • RE: BQ34Z100-G1: lerning cycle does not complete

    Hi, 1) BQ34Z100-G1 Technical Reference Manual (Rev. A) Chapter 11 in the trm has a better learning cycle steps in my opinion. Here is a more general document. Achieving The Successful Learning Cycle 2) The battery needs to be fully relaxed before proceeding…

  • BQ34Z100-G1: Learned Status does not change to 5 after full charge

    Part Number: BQ34Z100-G1 Other Parts Discussed in Thread: BQ34Z100 Tool/software: Hello, I'm currently trying to do a learning cycle for our 12s4p Lithiom Ion Battery without any success. I followed the guild "How to Complete a Successful Learning…
    • Answered

  • BQ34Z100-G1: Remaining Capacity estimation when user rate (mAh) and Reserve Cap (mAh) are used

    Resolved
    Part Number: BQ34Z100-G1 Tool/software: Hi, How does the BQ34Z100-G1 estimate the remaining capacity when load select = 6 and reserve cap-mAh is used? does it subtract the reserved capacity from the remaining capacity so when RC = 0mAh it is effective…
    • Resolved

  • BQ34Z100-G1: TS pin internal pull down resistor

    TI Thinks Resolved
    Part Number: BQ34Z100-G1 Other Parts Discussed in Thread: BQ34Z100-R2 Tool/software: Dear Sir/Madam, I would like to use your BQ34Z100-R2 chip for measuring battery parameters. I have some questions regarding temperature measurement using an NTC thermistor…

  • BQ34Z100-G1: Problem with the full unseal and to read Firmware Version

    TI Thinks Resolved
    Part Number: BQ34Z100-G1 Tool/software: Hello, When I try to full unseal the gauge, after 20s, I get a failure message from full un seal the gauge. During programming, the full un seal code is not touched. The timer for the un seal (0x01403672) is too long…

Didn't find what you are looking for? Post a new question.