Answered

• BQ34Z100-R2: bq34z100-r2 voltage calibration

  

  Piotr Radecki

  Resolved

  Part Number: BQ34Z100-R2 Other Parts Discussed in Thread: EV2400 Tool/software: Hi! I am getting started with bq34z100-r2 fuel gauge for pack of 4 NiMH batteries with 3100mAh capacity. Single cell voltage is 1.2V. So the entire pack voltage is 4.8V. I…

  • Resolved

  • 6 months ago
  • Power management
  • Power management forum

• BQ34Z100-R2: BQ34Z100-R2:

  

  taehwan lee

  TI Thinks Resolved

  Part Number: BQ34Z100-R2 Tool/software: Hi, I am luisI am using the BQ34Z100-R2 to control 4 battery indicator LEDs. I have successfully implemented the functionality to blink 1 to 4 LEDs based on the battery's state of charge (25%/50%/75%/100%). However…

  • 7 months ago
  • Power management
  • Power management forum

• BQ34Z100-R2: BQ34Z100-R2

  

  Benard Junior Muhindo

  TI Thinks Resolved

  Part Number: BQ34Z100-R2 Other Parts Discussed in Thread: EV2400 Tool/software: Can the battery chemistry of BQ34Z100-R2 be programmed without EV2300 or EV2400 kit?

  • 10 months ago
  • Power management
  • Power management forum
Answered

• BQ34Z100-R2: Errata applicability

  

  Saravanakumar Irulappan

  Resolved

  Part Number: BQ34Z100-R2 Other Parts Discussed in Thread: BQ34Z100 , Tool/software: Hi, We found an errata online for the older part BQ34Z100. Is this errata applicable for new part BQ34Z100-R2? Please confirm. Errata bq34z100 Errata …

  • Resolved

  • 1 month ago
  • Power management
  • Power management forum

• BQ34Z100-R2: Request for circuit diagram confirmation

  

  Masashi Mineda

  TI Thinks Resolved

  Part Number: BQ34Z100-R2 Tool/software: Dear Sirs and Madams, Since it contains confidential information, it cannot be made public via E2E, but would it be possible for you to check the BQ34Z100-R2 circuit diagram by message or something? Regards…

  • 4 days ago
  • Power management
  • Power management forum

• BQ34Z100-R2: Request for design support

  

  Siby Ettikalayil Varghese

  TI Thinks Resolved

  Part Number: BQ34Z100-R2 Tool/software: We have decided to use BQ34Z100-R2 in one of our application. The system is completely working on the battery. This device is used to monitor the battery of the system. The battery we are planning to use is Ni…

  • 16 days ago
  • Power management
  • Power management forum

• RE: BQ34Z100-R2: BQ34Z100-R2 Learned Status Stuck at 0x4 - FC setting early

  

  Diego

  Hi Kris, You FC bit set because you have FC set % = 100, Therefore when SOC reports 100% the FC flag will set. Please change FC set % = -1 until the learning cycle is complete. The gauge will now use Valid charge termination conditions to detect full…

  • 3 months ago
  • Power management
  • Power management forum
Answered

• BQ34Z100-R2: Reverse Polarity

  

  Saravanakumar Irulappan

  Resolved

  Part Number: BQ34Z100-R2 Tool/software: Hi, Is there any reverse polarity detection built-in with the IC? Regards, Saravana

  • Resolved

  • 1 month ago
  • Power management
  • Power management forum

• BQ34Z100-R2: How to read NominalAvailableCapacity() and FullAvailableCapacity()?

  

  Steve Tecza

  TI Thinks Resolved

  Part Number: BQ34Z100-R2 Tool/software: The TRM for the BQ34Z100-R2 says: NominalAvailableCapacity() and FullAvailableCapacity() are the uncompensated (no or light load) versions of RemainingCapacity() and FullChargeCapacity(), respectively. …

  • 21 days ago
  • Power management
  • Power management forum

• BQ34Z100-R2:

  

  Ankit Ahlawat

  Part Number: BQ34Z100-R2 Tool/software: Hi sir, I am using bq34z100-r2 , sealed acid battery 12v 7Ah.What is the importance of the terminate voltage? Design capacity - 7000mAh Design voltage -> 5000mV by using the volt scale as 2 Number of cells…

  • 3 months ago
  • Power management
  • Power management forum

Didn't find what you are looking for? Post a new question.