Search tips
Showing 110 results View by: Thread Post Sort by

  • BQ35100EVM-795: "The detected device is not compatible with this application": Troubles with using BQ35100EM-795 Eval Board and 3.6 Li-SOCl2 battery

    Part Number: BQ35100EVM-795 Other Parts Discussed in Thread: BQSTUDIO , EV2400 Dear all, I bought the BQ35100EVM-795 EvalBoard but I have had some troubles during its use. As a matter of fact, once I have prepared the setup as shown on the User…
    • Answered

  • BQ35100EVM-795: FOR THE Bq35100-Does negative current indicated battery discharge?DOCUMENATION UNCLEAR-REQUEST ACTUAL ANSWER FROM EXPERT

    Resolved
    Part Number: BQ35100EVM-795 Other Parts Discussed in Thread: BQSTUDIO Hello, I'm currently reading a negative current on the bq35100evm with a powers supply and 8 ohm load connect. The documentation (Technical Reference Manual) appears to indicate positive…
    • Resolved

  • BQ35100EVM-795: BQ35100EVM-795

    TI Thinks Resolved
    Part Number: BQ35100EVM-795 Other Parts Discussed in Thread: BQ35100 , EV2400 , BQSTUDIO Dear Madam,Sir, I've a battery powered door lock design which use FANSO ER14505M 3,6V LISOCL2 primary battery. I like to use BQ35100 for measuring the correct…
    • Answered

  • BQ35100EVM-795: bq35100 flash write and access mode at purchase time -- Mode change required?

    Resolved
    Part Number: BQ35100EVM-795 Hello, I have the bq35100evm. I can read from flash fine currently, but cannot write. I JUST want to test writing. I'd like to avoid messing with the SHA stuff currenlty. How do I write to flash on a brand new device? Is the…
    • Resolved

  • BQ35100EVM-795: SOH value reading is incorrect

    TI Thinks Resolved
    Part Number: BQ35100EVM-795 Other Parts Discussed in Thread: BQSTUDIO Hello, The BQ35100EVM-795, that I'm working with, can not recognize the correct SOH value of the battery. 1) The circuit connection is as at the image below: * All the jumpers…

  • BQ35100EVM-795: Unable to trigger New Battery command and set Operation Config A register to EOS mode using BQStudio application software

    Part Number: BQ35100EVM-795 Other Parts Discussed in Thread: BQSTUDIO Hi, Used BQStudio version - 1.3.101 Unable to trigger New battery command after following steps - 1) Start Scan 2) Gauge Enable 3) Set security mode to Sealed 4) Set…
    • Answered

  • BQ35100EVM-795: SOH reduced by 2 percent after every GE pin toggle while gauging a cr2032 battery

    Resolved
    Part Number: BQ35100EVM-795 Hi, When I gauge a CR2032 battery using the State of Health (SOH) method, I initially inserted the battery into a CR2032 battery holder and connected it to the +Bat and -Bat terminals. I also connected a 165 Ohm resistor…
    • Resolved

  • BQ35100EVM-795: How to measure remaining capacity of a Li-SOCI2 with BQ35100EVM and BQStudio

    TI Thinks Resolved
    Part Number: BQ35100EVM-795 Other Parts Discussed in Thread: BQSTUDIO , EV2400 , BQ35100 I have the bq35100EVM board connected to the EV2400 and started BQstudio. I updated the Configuration Operation Config A to set EOS mode with GMSEL1 = 1 and GMSEL0…
    • Answered

  • BQ35100EVM-795: Unable to read updated voltage values without cycling power

    Resolved
    Part Number: BQ35100EVM-795 Other Parts Discussed in Thread: BQ35100 , MSP430FR5994 , BQSTUDIO , EV2400 I am using an MSP430FR5994 to read the voltage supplied to the BQ35100 via I2C using the command 0x08, as seen in the code below. The issue I am running…
    • Resolved

  • BQ35100EVM-795: Saft LSH14 not listed in Battery management studio

    TI Thinks Resolved
    Part Number: BQ35100EVM-795 Other Parts Discussed in Thread: BQ35100 , BQSTUDIO Hello, I am using BQ35100 EVM with Saft LSH14, but while selecting the battery chemistry I was not able to find Saft LSH14 in the list of batteries. I have few question…

Didn't find what you are looking for? Post a new question.