Because of the holidays, TI E2E™ design support forum responses will be delayed from Dec. 25 through Jan. 2. Thank you for your patience.



Search tips
Showing 254 results View by: Thread Post Sort by

  • BQ76952EVM: quesion BQ76952EVM about bqstudio data graph

    TI Thinks Resolved
    Part Number: BQ76952EVM Other Parts Discussed in Thread: BQSTUDIO Hi Max :) Thank you for you reply. I understand it. >Hi Awatch, >I believe that the Data Graph is limited to only 6 variables, however you can take a log of all the basic parameters with…

  • BQ76952EVM: BQ76952EVM test

    Part Number: BQ76952EVM Hi expert， I am studying BQ76952EVM. I disable the COV in CHG FET Protection A, but when cell overvoltage is occured, the CHG FET is still be off. I want to control the CHG FET by host, so it only needs to report the COV fault…
    • Answered

  • BQ76952EVM: Detection voltage error for some cells using BQ76952

    Resolved
    Part Number: BQ76952EVM Other Parts Discussed in Thread: BQ76952 I am using BQ76952 to detect the cell voltage. However, some voltage cell detection is not right. I assume it may be becuase I enable the balancing function. Can you tell me how to avoid…
    • Resolved
    • Answered

  • BQ76952EVM: BQ7695203

    Resolved
    Part Number: BQ76952EVM Other Parts Discussed in Thread: BQ34Z100 Hi Sunna, I want to use Read PassQ register and updating performance parameter like SOC, Charge/Discharge Ah. but sometimes i have observe that SOC decreasing very fastly . (1) Whenever…
    • Resolved

  • BQ76952EVM: quesion BQ76952EVM about bqstudio data graph

    TI Thinks Resolved
    Part Number: BQ76952EVM Other Parts Discussed in Thread: BQSTUDIO Hi! :) I using BQstudio with BQ76952EVM. I have some question for Data Graph This device has 16ch battery monitor, but BQ studio can dispray only 6ch. I want dispray 16ch with BQ76952EVM…
    • Answered

  • BQ76952EVM: Cannot program OTP with Stack Voltage SHUTDOWN >12v

    Resolved
    Part Number: BQ76952EVM Other Parts Discussed in Thread: BQ76952 , BQSTUDIO I have a 30v stack of Li batteries. I can load all registers into the BQ76952. I can continue communicating with the part by sending the SET_CFGUPDATE command before lowering the…
    • Resolved

  • BQ76952EVM: BQ76952EVM

    Part Number: BQ76952EVM Other Parts Discussed in Thread: BQSTUDIO , Hi I am using BQ76952EVM with BQStudio. I am trying to Enable LDO (REG1, REG 2) i.e in data memory REG12 config = dd and REG0 config =1; But I do not see do not see 3.3 of REG1 and REG2…
    • Answered

  • BQ76952EVM: Data read back does not match settings

    Resolved
    Part Number: BQ76952EVM As can be seen in the bottom line below, PF_EN is True and FET_EN is False. I verified that Settings:Manufacturing:Mfg. Status Init was 0x0010 so both of these bits are wrong. I even wrote that byte again with no effect. I am using…
    • Resolved
    • Answered

  • BQ76952EVM: Monitoring Cell

    Resolved
    Part Number: BQ76952EVM Other Parts Discussed in Thread: BQ76952 Hi expert I am grateful to be able to use a good product. I have a question about how to set up cell V alarms in BQ Studio. BQ Studio can be monitoring Max 16 cells, but I'm monitoring only…
    • Resolved

  • BQ76952EVM: BQ76952

    TI Thinks Resolved
    Part Number: BQ76952EVM Hi Team I am using BQ76952EVM,Can you tell me how the circuit in the red circle works?How should I choose those component parameters? Thanks.

Didn't find what you are looking for? Post a new question.