• 

  Andy Neil

  • 8 months ago
  • Sub-1 GHz
  • Sub-1 GHz forum

  CC1070: SmartRF Studio 6 not working - tvicport.sys

  Part Number: CC1070 It seems the current version, SmartRF Studio 7, doesn't support the CC1070 - I need SmartRF Studio 6. So I downloaded & installed Setup_SmartRF_Studio_6.13.1.exe But when I run it and select CC1070, I get: This...
• 

  TER

  • 9 months ago
  • Sub-1 GHz
  • Sub-1 GHz forum

  RE: CC1125: cc1070 migration

  It depends on what you will find easier but since you don't know CC1070 in the first place I would assume that it would be easier to write code directly for CC1125 without looking too much on what has done before. Then you just have to learn one radio...
• 

  Scot Cowley

  • over 2 years ago
  • Sub-1 GHz
  • Sub-1 GHz forum

  RE: CC1310: Legacy application (TX only)

  It was used due to a legacy cc1070 (chipcon) project. This would be the second project keeping the legacy going. There were some interesting choices made which makes it hard to follow a payload format. Preamble - 30 bits (non manchester) Data ...
• 

  Edward Blair

  • over 3 years ago
  • Sub-1 GHz
  • Sub-1 GHz forum

  LAUNCHXL-CC1310: External calibration of the RF Crystal Frequency

  • Resolved

  . CC1070 , CC1101, etc.) we have made use of the ability to output the RF crystal signal (divided down
• 

  BrunoG BrunoG

  • over 8 years ago
  • Other wireless
  • Other wireless technologies forum

  CC1070

  Hi i have e device who use the CC1070 to transmit weather data to a receiver (who use CC1021): 902 to 928 mhz (the device is made for usa) xtal: 14.7-508. I have the same device (but built for Europe) who use 868mhz, what can i do to make the device...
• 

  BillySugger

  • over 5 years ago
  • Other wireless
  • Other wireless technologies forum

  Need help with UART link from cc1070 to cc1020

  Hi All, I have inherited an RF transmitter project which transmits a device ID as a UART, and I have been asked to develop a receiver to detect and display the ID. The transmitter hardware is already designed and has been in manufacture for some time...
• 

  Gin Rossouw

  • over 7 years ago
  • Other wireless
  • Other wireless technologies forum

  CC1070 impedance measurement

  Hi Folks I have been tasked to investigate the impedance matching on a product of ours, that uses a CC1070 transmitter IC. I need some information / confirmation on the setup to measure the impedance looking into the CC1070 matching network from the...
• 

  Y-G Sung

  • over 10 years ago
  • Other wireless
  • Other wireless technologies forum

  CC1070 with MSP430F

  I am trying to interface the RF chip CC1070 with the MSP430F249 processor. Is there any helpful information such as sample code, books, web-site, etc to develop a interfacing code? Thanks in advance
• 

  Terry16065

  • over 8 years ago
  • Other wireless
  • Other wireless technologies forum

  CC1070 Eval Board

  TI Thinks Resolved

  Is there an eval board for the CC1070? I see the reference design but I need an actual board.
• 

  Mihir Gupta1

  • over 8 years ago
  • Other wireless
  • Other wireless technologies forum

  Design for CC1101 and CC1070 for 403 MHz?

  • Resolved

  I have both CC1101 and CC1070 , and I want a very low power, short range (less than 10 m

Didn't find what you are looking for? Post a new question.

• Ask a new question