Search tips
Showing 1,355 results View by: Thread Post Sort by
    Answered

  • RE: CC2531: OAD resources

    Resolved
    CC2430 is obsolete but the OAD process is the same to CC2530. I don’t remember exactly if old Z-Stack provides OAD example for CC2430. If not, you can refer to how CC2530 OAD is done in Z-Stack to implement on CC2430.
    • Answered

  • CC2430: How can the wireless module(CC2430F128) be set up by software(SmartRF_Studio_7-1.3.2 ) to transmit data without carrier?

    Resolved
    Part Number: CC2430 Now I need to do the frequency deviation and power test of the wireless module (CC2430F128) by software(SmartRF_Studio_7-1.3.2 ) . I have already known how to set the fixed frequency and the fixed power transmission, but How can the wireless…
    • Resolved

  • CC2430: RF Studio

    Part Number: CC2430 Other Parts Discussed in Thread: CC2530 , CC2630 I need your help to understand whether Smart RF studio 7 SW could display RX sensitivity of CC2430. I am able to measure RSSI and PER at given input signal level but I like to know the…

  • CC2430: How much memory available for programmes?

    Part Number: CC2430 Other Parts Discussed in Thread: CC2650 I'm looking at the data sheet for the CC2430, and it mentions 8k ram, and 32, 64 or 128kB programmable memory. Is any of the 8k available for application firmware, or just the 32 - 128kB…

  • CC2430: Cannot Initialize

    Part Number: CC2430 after spending hours finally Carelink is detected in TI smart RF studio 7 SW, however as you could see I am unable to initialize it correctly

  • CC2530: Zstack 3.0.2 loses RF frames

    TI Thinks Resolved
    Part Number: CC2530 Other Parts Discussed in Thread: CC2430 , Z-STACK , SIMPLICITI , CC2538 Hi everybody, I am using CC2530 with Zstack 3.0.2 for a project with several Routers and a single Coordinator. Normally they work alone (they are in movement), without…

  • CC-DEBUGGER: Application Help

    TI Thinks Resolved
    Part Number: CC-DEBUGGER Other Parts Discussed in Thread: CC2541 , CC2540 , CC2543 , CC2545 , CC2544 , CC2533 , CC2530 , CC2531 , CC2511 , CC2510 , CC2431 , CC2430 Hello Team, Is there a is way to use a 10-pin CC debugger on a 14-pin JTAG? Regards, Renan

  • RE: CC2652PSIP: CC2652PSIP ZigBee protocol customization

    Hi Ryan. Thanks for reply. For some reason it was decided ages ago to change something there and I am searching for replacement. CC2430 allowed this, from manual: Maybe you know which modern part can be used as replacement? Regards. Mike

  • The DMA of CC2530/CC2430 is designed badly.

    Other Parts Discussed in Thread: Z-STACK The UART-DMA in z-stack,because there is no DMA-counter that counts how many data has been transmit,the _hal_uart_dma have to set 2-byte transmit.By this way,when Uart Buffer is overflow,the uart-RX will crash. …

  • Problem Zigbee cc2430

    Other Parts Discussed in Thread: CC2431 , CC2430 , Z-STACK , CC2530 , CC2531 , CC2538 Hello everybody I am using Zigbee to communicate two devices (cc2430/cc2431). My problem is that sometimes the message received is incorrect and always same ( 0x02 0x00 0xD3…

Didn't find what you are looking for? Post a new question.