Search tips
Showing 140 results View by: Thread Post Sort by

  • CC2652P7: 802.15.4 with CC2652P7

    Part Number: CC2652P7 Other Parts Discussed in Thread: CC2652PSIP , CC1352P7 , LP-CC1352P7 Tool/software: I have been assigned the task of writing a 802.15.4 application for the CC2652P7. I had started working with with the "Collector" project for CC2652PSIP…
    • Answered

  • CC2652P7: dynamically changing advertising packet.

    Resolved
    Part Number: CC2652P7 Tool/software: Hello. I am developing an application on the CC2652P7 processor, and the project is based on an example from the SDK. I have two devices, one of which acts as the master and the other as the slave. The master device…
    • Resolved
    • Answered

  • CC2652P7: Zigbee Antenna Issues

    Resolved
    Part Number: CC2652P7 Tool/software: Hi everybody, I am really frustrated right now, because my custom layout does not work as intended. What I have did was copying the hardware guide (I know its not the best solution, but for me its the only one for…
    • Resolved

  • CC2652P7: Question on UART Baud Rate Automatic Detection in bootloader.

    TI Thinks Resolved
    Part Number: CC2652P7 Tool/software: Hi teams, My customer is using the CC2652P7 with ROM bootloader. When the host MCU is sending 0x55, CC2652P7 will also reply 0x55 in the same time. Please see the picture below. Is this the correct mechanism…
    • Answered

  • CC2652P7: OSAL SNV erase multi Customer's NV IDs

    Resolved
    Part Number: CC2652P7 Other Parts Discussed in Thread: SYSCONFIG , UNIFLASH Tool/software: Hi, I would like to erase multiple customer-specific NV (non-volatile) IDs approximately 100 entries totaling around 1 KB. However, the available OSAL SNV API…
    • Resolved

  • CC2652P7: DSSS PHY O-PQSK

    TI Thinks Resolved
    Part Number: CC2652P7 Tool/software: Does the IEEE 802.15.4 interface comply with the generic requirements of a PHY DSSS O-PQSK operating in the 2450 MHz band in accordance with the IEEE 802.15.4 standard?
    • Answered

  • CC2652P7: CC2652P7: soft reset command

    Resolved
    Part Number: CC2652P7 Hi, How do I soft reset the CC2652P7 chip? This has to be done upon receiving a command over UART. Thanks Karthik
    • Resolved

  • CC2652P7: Application issues.

    TI Thinks Resolved
    Part Number: CC2652P7 Tool/software: Hi team, The attachment contains the schematic diagram and PIN MAP file. Please help review the design changes based on CC2652P7, which mainly involve changes in GPIO configuration. Thank you! CC2562P7_Pin_MAP…
    • Answered

  • CC2652P7: Implementability analysis，A coordinator, device that requires routing mode.

    Resolved
    Part Number: CC2652P7 Other Parts Discussed in Thread: CC2674P10 , CC2652P , CC2530 , Z-STACK Tool/software: Hello​ Feasibility Analysis: 500 Powered Devices in a 3m×5m Room Using Zigbee Communication to Transmit Status Within 20 Seconds ​ ​ Configuration…
    • Resolved
    • Answered

  • CC2652P7: Fail bond device to Windows 10

    Resolved
    Part Number: CC2652P7 Tool/software: Hello. We are developing devices based on the CC2652P7 chip using the SDK example. We have two identical BLE devices with different MAC addresses. We are also developing software for Windows 10 using the Plugin.BLE…
    • Resolved

Didn't find what you are looking for? Post a new question.