Search tips
Showing 60 results View by: Thread Post Sort by

  • CSD17308Q3: Please help provide comparison table

    TI Thinks Resolved
    Part Number: CSD17308Q3 Other Parts Discussed in Thread: CSD17578Q5A , CSD17578Q3A , CSD17581Q5A , CSD17576Q5B Hi Team There good new that we could DIN our CSD17308Q3, And need you support following requirement to make sure DWIN ,THX Please help provide…
    • Answered

  • CSD17308Q3: Emulation parameters

    Resolved
    Part Number: CSD17308Q3 Other Parts Discussed in Thread: CSD Hello Sr, I am going to use this N-FET to make a resonant tank,before to start this project I need a simulation with this FET,pls hlep to provide those parameters below for further evaluation…
    • Resolved

  • CSD17308Q3: REACH documentation

    TI Thinks Resolved
    Part Number: CSD17308Q3 The REACH status of CSD17308Q3 is listed as "Affected", but I am not able to find any more documentation on this. The Restricted Chemical Test Results report for this device is limited only to RoHS and does not address…
    • Answered

  • CSD17308Q3: Pspice model report error in cadence

    Resolved
    Part Number: CSD17308Q3 Hi expert, I`m using CSD17308Q3 Pspice model to simulate in cadence/virtuoso_spectre, it report "Cannot run the simulation because the syntax error `Unexpected end of file. Expected equals sign, numeric value or string value' was…
    • Resolved

  • CSD17308Q3: MOS damage risk

    TI Thinks Resolved
    Part Number: CSD17308Q3 Hi Sir, customer use CSD17308 for super Cap application, there is currently a problem as follow: 1. this is customer the schematic, R3 and C11 is soft start function but because there is already 2A of energy before reach the Vth…
    • Answered

  • BQ24715: layout of mosfet CSD17308Q3

    Resolved
    Part Number: BQ24715 Other Parts Discussed in Thread: CSD17308Q3 Hi, We are using BQ24715 as charger ic for application. While going through the EVM module of BQ24715 the Fet CSD17308Q3 ( Q4 in data sheet and Q2 in EVM module) had a large area left out…
    • Resolved

  • CSD17308Q3: Unencrypted model request

    TI Thinks Resolved
    Part Number: CSD17308Q3 Other Parts Discussed in Thread: CSD17559Q5 Hello, We are working on a novel water-purification system and I am running some simulations on LTspice. The proposed design will make use of the CSD17308Q3 and CSD17559Q5 MOSFETs. Would…
    • Answered

  • CSD17308Q3: Body diode characteristics

    Resolved
    Part Number: CSD17308Q3 HI, Is the body diode Schottky in the CSD17308Q3? I can hardly find an answer in the datasheet. Thanks, Joshua Kim
    • Resolved
    • Answered

  • BQ40Z60EVM-578: CSD17308Q3's Datasheet says Vgs (Max) is +10/-8V and the output voltage of ACFET and HIDRV pins of EVM is more than 15V.

    Resolved
    Part Number: BQ40Z60EVM-578 Other Parts Discussed in Thread: CSD17308Q3 I'm confused with components selected by Ti design team. CSD17308Q3's Datasheet says Vgs (Max) is +10/-8V and the output voltage of ACFET and HIDRV pins of EVM is more than 15V…
    • Resolved
    • Answered

  • CSD17308Q3: The resistor between gate and source

    Resolved
    Part Number: CSD17308Q3 Dear, I use the CSD17308Q3 FET for a high-side switch as shown in the picture, in my circuit which imitates a TI's evaluation board of a driver IC, where the R1 = 5 KOhm, R2 = 10 Mega Ohm. The application is Li-Ion battery…
    • Resolved

Didn't find what you are looking for? Post a new question.