Search tips
Showing 14 results View by: Thread Post Sort by

  • CSD17501Q5A: similar spec p2p

    • Resolved
    Part Number: CSD17501Q5A Hi team, Do you have the recommend p2p parts for below and sample

  • RE: BQ76920: Can CSD19536KTT FET should be recommended for BQ76920 charging & discharging?

    Hi, This MOSFET should work fine for the BQ76920, but it is beyond what is needed. The BQ76920 EVM uses the CSD17501Q5A which is rated for lower voltage. Best regards, Matt

  • DLPA3005: The high side MOS is different between low side MOS in DLPA3005 PMIC & LED DRIVER

    • Resolved
    is CSD17501Q5A . Is there any reason for this different?

  • SOA CSD17501Q5A

    Kindly help me in understanding SOA of CSD17501Q5A. 1. What is significance of RDS(on) linit area. 2.What is the pulse duty cycle in SOA when pulsed current is for 1sec, 100ms. I have to design a CDS fet as switch. In datasheet it claims to...

  • Footprints for components used in the EVM

    • Resolved
    CSD17501Q5A MSP430F5514 (preferably both xBGA and HTQFP) PS: We are using Altium Designer 16 Thank you

  • CSD17501Q5A CSD17552Q3A models for TINA-TI

    • Resolved
    Is there a TINA-TI model available for the CSD17501Q5A NMOS? Also for the CSD17552Q3A NMOS. When I

  • SOA of CSD17501Q5A

    Kindly help me to understand SOA of mosfet especially circled area. When do RDS(on) linit occurs & what is pulse width in case of pulsed current i.e. 1sec,100ms etc. I am designing a circuit using above mosfet as switch to pass 10A current,...

  • Transfer Char Mosfet & TI's SLUP170 Notes & CSD17501Q5A

    1. I have seen many transfer char of different fets, some are measured at Ta, some with Tc & some without any specifiaction only temp is given i.e its not mentioned whether its case or ambient or junction. Why is so. 2. I got this problem because...

  • RE: UCC3806 reference design and simulation model

    Hello, The UCC3806 is a dual output controller though it can be used in a flyback where only one of the outputs are used to drive the switch it might be better to choose a single output controller. Look at page 46 of the attached under General Purpose...
    • Power management guide 2011.pdf

  • RE: Low operating voltage version of a TL494?

    Mark, see teh attached Power Management Guide Page 43 John
    • Power management guide 2011.pdf

Didn't find what you are looking for? Post a new question.


All content and materials on this site are provided "as is". TI and its respective suppliers and providers of content make no representations about the suitability of these materials for any purpose and disclaim all warranties and conditions with regard to these materials, including but not limited to all implied warranties and conditions of merchantability, fitness for a particular purpose, title and non-infringement of any third party intellectual property right. No license, either express or implied, by estoppel or otherwise, is granted by TI. Use of the information on this site may require a license from a third party, or a license from TI.

Content on this site may contain or be subject to specific guidelines or limitations on use. All postings and use of the content on this site are subject to the Terms of use of the site; third parties using this content agree to abide by any limitations or guidelines and to comply with the Terms of use of this site. TI, its suppliers and providers of content reserve the right to make corrections, deletions, modifications, enhancements, improvements and other changes to the content and materials, its products, programs and services at any time or to move or discontinue any content, products, programs, or services without notice.

TI worldwide | Contact us | myTI login | Corporate citizenship

TI is a global semiconductor design and manufacturing company. Innovate with 100,000+ analog ICs and
embedded processors, along with software, tools and the industry’s largest sales/support staff.

© Copyright 1995-2020 Texas Instruments Incorporated. All rights reserved.
Trademarks | Privacy policy | Terms of use