• 

  itabi

  • over 1 year ago
  • Power management
  • Power management forum

  CSD18536KCS: ESD Ratings (HBM/CDM)

  TI Thinks Resolved

  Part Number: CSD18536KCS Hello, We would like to know the ESD ratings for CSD18536KCS. Could you teach us the value of HBM(MM) and CDM. We couldn't find this information in the datasheet. Best Regards, itabi
• 

  John Wallace1

  • over 1 year ago
  • Power management
  • Power management forum

  RE: CSD18536KCS: Is this device automotive qualified?

  Hi Manuel, Thanks for the inquiry. Unfortunately, none of TI's MOSFETs are automotive qualified and there are no plans to get automotive qualification on any of our devices.
• 

  JunNam Park

  • over 2 years ago
  • Power management
  • Power management forum

  CSD18536KCS : Is there a way to reduce or eliminate switching noise?

  TI Thinks Resolved

  Part Number: CSD18536KCS We are designing the inverter circuit using the MOSFET CSD18536 and Driver-UCC3895. The input voltage is 48V, the output voltage is 400V, and the circuit is being designed with a phase shift method of 300W output. However...
• 

  John Wallace1

  • 10 months ago
  • Power management
  • Power management forum

  RE: Power Mosfet calculation for 100V@200Amp current rating

  Hi Abhishek, For your application, you want to control the inrush current when making a hot plug connection. You may want to consider a hot swap or high side controller to drive the FETs. One example is the LM5060 high side protection controller. It...
• 

  Herman Theodorus

  • over 1 year ago
  • Power management
  • Power management forum

  RE: TINA/Spice/CSD18536KCS: Importing encrypted spice models of ti parts into TINA-TI ,for simulation

  Hi Anil, Unfortunately, due to LTspice user agreement, we cannot support LTspice. Herman
• 

  Marcoo Z

  • over 4 years ago
  • Power management
  • Power management forum

  CSD18536KCS high current low voltage limitations?

  • Resolved

  am thinking of using the CSD18536KCS due to its high current capability but I have a question about
• 

  Hiroshi Doi35

  • over 2 years ago
  • Power management
  • Power management forum

  UCC25630-1EVM-291: How to built in UCC25612-2

  • Resolved

  extension wire from SOT-23. two CSD18535KCS or CSD18536KCS . two UCC24612-2DBVT extension board and wires
• 

  Bart Basile

  • over 2 years ago
  • Simulation, hardware & system design tools
  • Simulation, hardware & system design tools forum

  RE: TIDA-00120: Adjust the EVM to 48V and 40A

  Shai, As the guide states, there are two parameters you will need to adjust in the FET selection to support your use case; voltage rating and package. An 80-100V FET will be suitable, but you will also need to change the layout to support a TO-220 package...
• 

  Sungbin Suh

  • over 5 years ago
  • Motor drivers
  • Motor drivers forum

  Is drv8332 sufficient for 350W 48V hubmotor?

  • Resolved

  ). Technically, it will be about 6.5A continuous. is it safe? Or do i have to go with drv8302 + CSD18536KCS
• 

  Brett Barr1

  • over 4 years ago
  • Power management
  • Power management forum

  RE: Application of CSD18536KTT

  Mat, I actually wrote a blog about FET current ratings on datasheets and how they are basically bogus. If you want to learn a bit more about FETs or at least what their datasheet specs actually imply, you might want to check out the entire series. But...

Didn't find what you are looking for? Post a new question.

• Ask a new question