Search tips
Showing 13 results View by: Thread Post Sort by

  • LM5050-2: LM5050-2 with CSD19506KCS offset for Vgate not enough, what is wrong here?

    TI Thinks Resolved
    Part Number: LM5050-2 Other Parts Discussed in Thread: CSD19506KCS Relevant topic is : https://e2e.ti.com/support/power-management/f/196/p/876985/3244550#3244550 I don't know how to change from Resolve to not resolve status. I create separately circuit…
    • Answered

  • CSD19506KCS: peak diode recovery dV/dt

    Resolved
    Part Number: CSD19506KCS What is the dV/dt rating of this switch? Do you have a recommendation for another switch specified for >2V/ns? Best regards, Sean
    • Resolved

  • UCC27324: Switching Speed driving 3 x CSD19506KCS

    TI Thinks Resolved
    Part Number: UCC27324 Other Parts Discussed in Thread: CSD19506KCS , Hi, I have an application were a single UCC27324 (output channels in parallel) drives three CSD19506KCS in parallel. Each of the MOSFETs has separate 6ohm gate resistor. I want to decrease…
    • Answered

  • CSD19506KCS Thermal Considerations

    Resolved
    Other Parts Discussed in Thread: CSD19506KCS , SM72295 Hi, I have a question relating to thermal considerations for the CSD19506KCS N-Channel NexFET Power Mosfet. For the following values: Drain-to-Source Voltage, V(DS) = 12V Continues Drain Current, I…
    • Resolved

  • CSD19506KCS Solder Tab?

    Other Parts Discussed in Thread: CSD19506KCS I am currently planning on using 6 of the CSD19506KCS NexFETs to implement a 3 phase motor controller. I was left wondering however if the tab of these mosfets can be soldered to the board or if they must be…
    • Answered

  • CSD19536KCS: Eoss vs Vds data

    Resolved
    Part Number: CSD19536KCS Other Parts Discussed in Thread: CSD19506KCS , CSD18536KCS Hi Team, A customer requests us the data of “Eoss vs VDS” for the following 3 devices.　If you have any data to be able to share with customer, please support it.…
    • Resolved

  • DRV8323: MOSFETS heating up with weird sound on the borad

    Part Number: DRV8323 Other Parts Discussed in Thread: CSD19506KCS Hello, I'm using DRV8323 SPI version to command CSD19506KCS MOSFETS , with the following configuration: IDRIVEP_HS : 120 mA IDRIVEN_HS : 240 mA IDRIVEP_LS : 120 mA IDRIVEN_LS : 240 m…
    • Answered

  • RE: MOSFET In Constant Current mode

    Resolved
    Hi Vishal, After speaking with a colleague, I had a few more comments. First, I'd recommend reaching out to the MOSFET vendor to get their inputs and send a failed device to them for failure analysis. And second, TI also makes power MOSFETs although not…
    • Answered

  • TIDA-00120: Adjust the EVM to 48V and 40A

    Resolved
    Part Number: TIDA-00120 Other Parts Discussed in Thread: CSD19506KCS , CSD18532Q5B , CSD18536KCS Hello Team, in the Test Report - (PMP7605) it was mentioned that the EVM can be easily changed and adjusted to support 48V and 40A by just changing the MOSFETs…
    • Resolved

  • CSD19535KCS: looking for N channel Mosfet replacement for HUF75545

    TI Thinks Resolved
    Part Number: CSD19535KCS Other Parts Discussed in Thread: CSD19503KCS , CSD19501KCS , CSD19505KCS , CSD19506KCS Dear team, my customer are looking for N channel Mosfet replacement for existing design (see attached existing mosfet datasheet). The spec is: …

Didn't find what you are looking for? Post a new question.