Search tips
Showing 21 results View by: Thread Post Sort by
    Answered

  • RE: TIDA-01371: Follow the reference design, shall I remove those components which are canceled in tiduci3a.pdf, but still in Altium?

    Resolved
    Hello Sanjay， 1) Is your schematic same as TIDA-01371 schematic? A1: Yes. They are same. 2) Is your layout same as TIDA-01371 layout? A2: 99% similarity. 3) How many FETs have you connected in parallel with the LDO? A3: CSD19533KCS *3 in parallel…
    • Answered

  • RE: Matchable device recommendation : IPD60N10S4L-12?

    Resolved
    Hi Yue TANG, Thanks for the inquiry. The IPD60N10S4L-12 is in a TO-252 (DPAK) package. TI does not make any FETs in this package. Some alternatives to consider: CSD19533Q5A in 5x6mm SON package CSD19533KCS in in TO220 package CSD19537Q3 in 3x3mm…
    • Answered

  • TIDA-01371: floating posistive regulator 55V 6A continuous service

    Resolved
    Part Number: TIDA-01371 Other Parts Discussed in Thread: CSD19533KCS Hello, I would like to use the TIDA-01371 to have +55V @6A at the output, continuous service. I am expecting high PSRR and Low Drop Voltage. The circuit will be placed after an…
    • Resolved
    • Answered

  • TPSI3050-Q1: Schematic review & PSPICE simulation error.

    Resolved
    Part Number: TPSI3050-Q1 Other Parts Discussed in Thread: TPSI3050 Hi, The customer wrote a schematic of DC LINK PRE-CHARGE. An error occurs as a result of the PSPICE simulation. 1. Please review the schematic. 2. Please guide me on how to improve…
    • Resolved

  • LM5116: LM5116

    Part Number: LM5116 Other Parts Discussed in Thread: CSD19533KCS , CSD19535KCS , Hi, I'v designed a Buck converter using Webench. The controller is LM5116MHX/NOPB . ( webench.ti.com/.../webench5.cgi The MOSFETs are different from the design, made by TI…

  • RE: 100V next fet problems

    Here a pic to the CSD19533KCS working with no load at 200Khz. I have 10A driver close to the gate and almost no ring. Could you say why the mosfet is so lossy ? Thank you for help.
    • Answered

  • RE: Developing BLDC motor driver! Suggest MOSFET'S in KCS/To-92

    Resolved
    Dharmendra, Unfortunately, we do have any higher voltage MOSFETs at this time. The highest voltage P-Channel MOSFET we have currently is -25V. If you require 100V N-Channel MOSFETs, I suggest you look here. http://www.ti.com/lsds/ti/power-management…
    • Answered

  • DRV8350: First design and use DRV8350, Please help on reviewing and some questions.

    Resolved
    Part Number: DRV8350 Hi, My customer is the first time to use DRV8350H,so am I. please help to review their schematic and some questions. the schematic is as attached. Gate Drive Regen.pdf Q1:Please recommend the suitable component for pin 18…
    • Resolved

  • TPS92692: 400W LED Driver Circuit Review Request(TPS92692)

    TI Thinks Resolved
    Part Number: TPS92692 Hello team. We would like to ask for advice again regarding circuit design using TPS92692. We are going to make an LED driver board that can turn on 400W power LED board. Please look at the circuit and advise if there is any…
    • Answered

  • LM317: if the input voltage can be bigger than 40V and why Vo is limited to “37V”

    Resolved
    Part Number: LM317 Other Parts Discussed in Thread: , MLTLDO2EVM-037 Hi team, I am confused with the datasheet of LM317.In the first figure, we can see "In put voltage range" is up to 40V. In the second figure, we can also see the "Input-to-output…
    • Resolved

Didn't find what you are looking for? Post a new question.