Search tips
Showing 112 results View by: Thread Post Sort by

  • CSD19536KTT: TIDA 010030

    TI Thinks Resolved
    Part Number: CSD19536KTT Why Q30 272Amps is used for 30A BMS design? And what is the use of C68 and C69?
    • Answered

  • DRV8308 burning with CSD19536KTT

    Resolved
    Part Number: DRV8308 Other Parts Discussed in Thread: CSD19536 , CSD18511KTT , CSD19536KCS , 100A , CSD19536KTT , TEST Hello, I use an DRV8308 fo drive an BLDC with 18 Volt and approx 100 Ampere. WIth an IRFS7430 the MOSFET was so warm an a low duty of the…
    • Resolved

  • CSD19536KTT: RDC snubber design considerations

    TI Thinks Resolved
    Part Number: CSD19536KTT Hi, I want to design an RCD snubber circuit for my inverter board using CSD19536KTT , I'm unable to select the diode properly, Requesting your support for the design considerations and equations for selecting diode for RCD snubber…
    • Answered

  • CSD19536KTT: layout review for the mosfet placement

    Resolved
    Part Number: CSD19536KTT Other Parts Discussed in Thread: TIDA-00364 We have designed 3 phase full bridge MOSFET based inverter circuit and its Layout for motor controller application The Nominal operating voltage is 48 V , Maximum operating DC current is 200A , and pea…
    • Resolved
    • Answered

  • CSD19536KTT: Mosfet suggestion for solenoid driver application

    Resolved
    Part Number: CSD19536KTT Other Parts Discussed in Thread: CSD17307Q5A , CSD17304Q3 Hi everyone, Would you please suggest some mosfet part numbers for my application please ? Voltage: 24V Current: 10 Ampers Trigger will be 3.3V, PWM. Thanks!
    • Resolved

  • BQ76940EVM: Can we replace the onboard FET: AOB290L with CSD19536KTT?

    TI Thinks Resolved
    Part Number: BQ76940EVM Hello, My application requires a continuous discharge current of 30A, which can be easily done by CSD19536KTT I also noticed that the same FET is being used in TIDA 00792 . Both have nearly the same Vgth and Rds of CSD19536KTT is comparatively…

  • DRV8353: Using CSD19536KTT, But current is limiting to 15A

    TI Thinks Resolved
    Part Number: DRV8353 Other Parts Discussed in Thread: CSD19536KTT , Hello I have used 12 NMOS CSD19536KTT for 3 phase bldc motor control. DRV8353 is used as predriver and 1mE as current sense resistor for individual 3 phases. But unfortunately DC current…

  • RE: DRV8353: Using CSD19536KTT instead of CSD19532Q5B in large scale mass production.

    Sezen, You can change the shunt resistor and device settings to match your application and system current, this is explained in the datasheet section I mentioned above, 9.2.1.2.4 Sense-Amplifier Bidirectional Configuration ( DRV8353 and DRV8353R ). This should…

  • CSD19536KTT: Recommended operating condition Junction tempertature..

    TI Thinks Resolved
    Part Number: CSD19536KTT Hi, CSD19536KTT - Data sheet does not specified "the recommended operating Conditions Junction temperature value". Please provide the value. Note:- In Datasheet maximum junction temperature specified in absolute maximum…
    • Answered

  • CSD19536KTT: Qoss Calculation and check from datasheet

    Resolved
    Part Number: CSD19536KTT Hi, I am trying to calculate Qoss value from datasheet for type number is Csd19536ktt Mosfet. Could you please inform me about below subject? Qoss is 335nC for 50V according to the datasheet. But when I tried to calculate that…
    • Resolved

Didn't find what you are looking for? Post a new question.