Search tips
Showing 191 results View by: Thread Post Sort by

  • DAC161S997: Using two DAC161S997 for 4-20 mA output transmission

    TI Thinks Resolved
    Part Number: DAC161S997 Tool/software: Hi, I have read several threads about the problems you may have when using two DAC161S997 in the same circuit sharing any of the loop lines. In my case, I have the circuit below, for transmitting pH and electrical…
    • Answered

  • AMC0300D-Q1: AMC0300D-Q1 is causing linearity issues in current output of DAC161S997

    Resolved
    Part Number: AMC0300D-Q1 Other Parts Discussed in Thread: AMC1300B-Q1 , AMC1301-Q1 , , DAC161S997 , AMC0300D Hello Support Team, I was using the AMC1300B-Q1 as isolated current sense amplifer in my design, and the circuit was working well. I then replaced…
    • Resolved
    • Answered

  • DAC161S997: Loop Error Reporting with Excessive IAUX

    Resolved
    Part Number: DAC161S997 Tool/software: Can I just get a confirmation that this device will not report any loop errors in the STATUS register if the companion devices in the circuit (I AUX ) pull excessive current? From the linked question and a few others…
    • Resolved
    • Answered

  • DAC161S997: No loop current variation in (4 - 20mA) DAC161S997

    Resolved
    Part Number: DAC161S997 Hi TI community We are using DAC161S997 for 4- 20 mA current transmission. Below attached is the circuit schematics. We have a problem with bring up of this circuit, that is, while we writing various hex values to the DACCODE…
    • Resolved
    • Answered

  • DAC161S997: Not able to get Continuous output of DAC161S997

    Resolved
    Part Number: DAC161S997 Hi, I am interfacing DAC161S997 with MCU over SPI communication. When I Write the value to DACCODE register to set the output so it gives the output only for some milliseconds. For continuous output I am writing the value…
    • Resolved

  • DAC161S997: Increased HART Communication Errors Due to Earth Connection

    Part Number: DAC161S997 Tool/software: Hello Support Team, I am using the DAC161S997RGHT (WQFN-16) for the Current Output Section and the DAC8740HRGET (VQFN-24) for the HART section . My device's output current can work in 3 configurations: 3-wire…
    • Answered

  • DAC161S997: Load Sharing issue with Dual Channel 4-20mA transmitter when connected with Single Ended PLC inputs

    Resolved
    Part Number: DAC161S997 Tool/software: Team, We are using 2 x DAC161S997 for a dual-channel 4-20mA transmitter. Both the DACs share common ground with MCU and there is inbuilt isolation in transmitter circuit. In the field when both the transmitter…
    • Resolved
    • Answered

  • DAC161S997: HART Connection with AD5700-1

    Resolved
    Part Number: DAC161S997 Other Parts Discussed in Thread: LM2936 Tool/software: Hello, could you please check my connection pattern? I can recieve HART Signals but if i try to send Signals, I have no Modulation at all.
    • Resolved
    • Answered

  • DAC161S997: use of two DAC161S997 for the transmission of temperature and humidity

    Resolved
    Part Number: DAC161S997 Hello. I am trying to transmit temperature and humidity through 3 wires, +LOOP, -LOOP_temperature, and -LOOP_Humidity. Individually, they work perfectly, but when I connect them in parallel, they don't work. The current…
    • Resolved

  • DAC161S997: May I know the response time, accuracy and error data of DAC161S997

    TI Thinks Resolved
    Part Number: DAC161S997 Hi Team, I need to know the response time, accuracy, and error information about DAC161S997. Please help. Thanks.

Didn't find what you are looking for? Post a new question.