Answered

• DAC5578: Power on reset condition

  

  Shuhei Goto

  Resolved

  Part Number: DAC5578 Tool/software: Hi team, What is the condition to occur POR? Ex: VDD must be less than XX V for at least YY ms Best regards, Goto

  • Resolved

  • over 1 year ago
  • Data converters
  • Data converters forum
Answered

• DAC5578: Timing of Slave Address Fixation

  

  Ryu Yamashita

  Resolved

  Part Number: DAC5578 Hi team, Please tell me about slave addresses. Power is applied to AVDD, and the state of the ADDR pin is captured at the timing of POR release, at which point it is determined. After the slave address is fixed, there is no change…

  • Resolved

  • over 1 year ago
  • Data converters
  • Data converters forum

• DAC5578:DAC5578 LIBRARY

  

  YLmaz Ali

  TI Thinks Resolved

  Part Number: DAC5578 Other Parts Discussed in Thread: DAC7678EVM Hello, Is there a sample project or software library for DAC5578? Can you forward it to me? Thank you for your interest. Good work.

  • over 3 years ago
  • Data converters
  • Data converters forum
Answered

• DAC5578: Capacitive load and stability

  

  Yngve Eriksen

  Resolved

  Part Number: DAC5578 The data sheet for DAC5578SPW state "Capacitive load stability" is typ 1nF. What would the implication if the outputs where loaded with 1uF in parallel with 680Ohm? Is there a recommendation for serial output resistance if capacitive…

  • Resolved

  • over 3 years ago
  • Data converters
  • Data converters forum
Answered

• DAC5578: Zero-code error

  

  Y.Ottey

  Resolved

  Part Number: DAC5578 Dear TI Team There is the following description about Zero-code error. If you read this, is it correct to recognize that the Zero-code error changes depending on the output voltage? Also, if the Zero-code error changes depending…

  • Resolved

  • over 4 years ago
  • Data converters
  • Data converters forum

• DAC5578: Output pull down at device reset

  

  Yusuke Mukuno

  Part Number: DAC5578 Other Parts Discussed in Thread: DAC53204 HI Expert, My customer is considering about the dynamic voltage scaling for DCDC output with DAC5578. (DAC5578 is reused from prior project) https://www.ti.com/lit/an/sbaa342a/sbaa342a…

  • over 4 years ago
  • Data converters
  • Data converters forum

• DAC5578: DAC with initial high-impedance output(Hi-Z)

  

  Shenhua Zhang

  TI Thinks Resolved

  Part Number: DAC5578 Other Parts Discussed in Thread: DAC53401 Hi expert, Customer is seeking for DAC with below sepc: Channel number : >= 4 channel Output type: current or voltage both OK, for both type, need DAC can sink or source current. For…

  • over 5 years ago
  • Data converters
  • Data converters forum

• DAC5578: DAC latches wrong I2C address

  

  Emanuel Zimmermann

  TI Thinks Resolved

  Part Number: DAC5578 Other Parts Discussed in Thread: DAC121C081 , , DAC43608 Hello, I was guided to this forum by Jejomar Ildefonso from TI customer support. Here I found the following thread that might be related in some kind to our issue: DAC121C081…

  • over 5 years ago
  • Data converters
  • Data converters forum

• DAC5578: Asking for the DAC5578 setting and behavior

  

  SHH

  Part Number: DAC5578 Hi team, This DAC5578 design spec maximun output voltage is 600mV. Please provide your review ccomment. Questions 1. the EC send i2c_w rite 0x91 0x00 and oxffff 1 2, anything need to take care except this setting? 2. what is the…

  • over 8 years ago
  • Data converters
  • Data converters forum
Answered

• DAC5578: Outputcurrent

  

  Kuramochi Tadahiko

  Resolved

  Part Number: DAC5578 Hi, I received the following question from my customer. How much current can the DAC5578 output with all(8ch) channel simultaneously? Best Regards, Kuramochi

  • Resolved

  • over 8 years ago
  • Data converters
  • Data converters forum

Didn't find what you are looking for? Post a new question.