Search tips
Showing 55 results View by: Thread Post Sort by

  • DAC60508: Sample/Update rate (Msps) and settling time

    Part Number: DAC60508 Tool/software: Hello, i'm finding the right solution for my application where I need at least 800 ksps out of a DAC. I know the empirical rule that out sample rate is just the inverse of the settling time, as a maximum value…
    • Answered

  • DAC60508: Can I simultaneously update all DAC channels on several daisy-chained DACs

    Resolved
    Part Number: DAC60508 Tool/software: I have an application that uses 5 daisy-chained DACs (40 total DAC channels). I would like to update all 40 DAC channels then simultaneously update the outputs of all 40 DACs at the same time. Is that possible, and…
    • Resolved

  • DAC60508: Configuration of DAC60508 via SPI

    Part Number: DAC60508 Other Parts Discussed in Thread: MSPM0L1306 Hi, I want to configure the DAC60508 via SPI on the MSPM0L1306. Looking at the DAC60508 website, it seems that there is no sample code released to do the configuration on TI's MCU, is there…

  • DAC60508: address 0x01 data address is error

    Part Number: DAC60508 When use the DAC60508, should be read in upper four bits (15-12 bits) of address 0x01 during use 0010, now reading 1000, some errors, other address output data is normal. since the address is read-only, what is the reason?
    • Answered

  • DAC60508: Mid-scale PORST (with 1.25V output voltage) using internal reference possible at all?

    Resolved
    Part Number: DAC60508 Other Parts Discussed in Thread: DAC63204 Dear all, I've got a project in which I used a DAC60508MRTER because I was under the impression that it would start-up mid-scale using the internal reference of 2.5V. I expected 1.25V on all…
    • Resolved
    • Answered

  • RE: DAC60508: DAC60508ZCRTET

    Resolved
    My issue is now resolved Jones. thanks for all your support.

  • RE: DAC60508: Device ID Can't Always Be Read; Different Behavior Depending on Master uC Despite Correct SPI Mode, Etc.

    Hi Drew, It looks like you shared the STM reset command instead of the nRF reference disable command for the first screenshot. I do notice there is a small glitch on SDI in the nRF reset command (pink arrow). Is there any chance there is a similar glitch…

  • DAC60508: Cannot Read Device ID or Any Other Registers; SDO is Seemingly Random

    Part Number: DAC60508 Hello, I am relatively new to setting up and debugging SPI communication, so I appreciate your patience in advance. I've reflowed the DAC60508 to my board and tried to read the DEVICE ID unsuccessfully. I've verified the SPI mode…

  • DAC60508: No Output

    Part Number: DAC60508 Hi Team, VDD and VIO same supply 3.3V CS has 10K to VDD No MOSI from chip to be able to read REF to 2.2uF cap to gnd SPI clk mode 1 after a reset the default register set seems to be enabled thru the SYNC reg addr 02 - 0xFF00 (async…
    • Answered

  • DAC60508: DAC60508MCRTET/MRTE VDD=5.0V, Internal VREF.

    Resolved
    Part Number: DAC60508 I'd like to double check if what is the FS voltage would be when VDD = 5.0V, Vref = 2.5V (Internal) (DIV=1) and Gain = 2. Here is the circuit I have which is the same as the evaluation board. Thanks, -CD
    • Resolved

Didn't find what you are looking for? Post a new question.