Search tips
Showing 55 results View by: Thread Post Sort by
    Answered

  • DAC8718: LDAC delay issue and slew rate issue

    Resolved
    Part Number: DAC8718 Hi, I am making a project for a display driver where DAC8718 is used. I use the unipolar configuration in synchronous mode (LDAC triggered). I run into 2 issues at this time: 1) When the output is currently set to 0V and I want to…
    • Resolved

  • DAC8718: Dual-Supply Configuration Detection

    Part Number: DAC8718 Hello, I am trying to use the DAC8718SPAG in a dual-supply configuration (+5V AVdd, -5V AVss, +2.5V REF, +3.3V IOVdd ). I also have RSTSEL pin tied to IOVdd and USB/BTC pin tied to ground. My understanding is that the DAC should…
    • Answered

  • DAC8218: Comparison with DAC8718

    Resolved
    Part Number: DAC8218 Other Parts Discussed in Thread: DAC8718 , , DAC7718 Because of the supply chain issue with the DAC8718, we plan to use the DAC8218. The DAC is only used to test ADCs in our Controller Board (so the resolution of 14-bit or 12-bit is…
    • Resolved
    • Answered

  • DAC8718: SPI communication but no voltage output

    Resolved
    Part Number: DAC8718 Other Parts Discussed in Thread: MSP430F5517 , Hi everyone! I'm using an MSP430F5517 MCU to communicate with a DAC8718 over SPI. The nCS, SCLK, MOSI, and MISO signals between the two devices appear correct on the oscilloscope: …
    • Resolved

  • DAC8718: SPICE model

    TI Thinks Resolved
    Part Number: DAC8718 Hi, Do we have a spice model for DAC8718SPAG ? The only simulation file available is the IBIS model. Thank you. Regards, Maynard
    • Answered

  • DAC8718: DAC8718 power-source influence the output.

    Resolved
    Part Number: DAC8718 Hi support: When my board use ITECH as power source, the DAC8718 can out -7.5 - 7.5v, but i change to common power source.the DAC8718 output 0-15v and my goal is that DAC8718( Dual-Supply ) can out put -7.5 -7.5 v. the schematic as follow…
    • Resolved

  • DAC8718: DAC8718 dual power can't output negative voltage

    TI Thinks Resolved
    Part Number: DAC8718 Hi: PCB layout as follow: AVDD:+15v AVSS:-15V DVDD 5V IOVDD: 3V Vref :2.5V This PCB is designed for dual power,but I only can adjust the DAC value from 0 - 15V without setting the the offset register. Should I pay attention to the…

  • DAC8718: Fixed offset of 10V on all Analog output

    Part Number: DAC8718 Sir, I hope you are fine. I have been using DAC8718 for more than 2 years. As per datasheet of DAC8718, specific power up sequence should be followed. First, Digital supply (IOVDD and DVDD) both tied to 3.3V then Analog supply (AVDD…

  • DAC8718: NC pins

    TI Thinks Resolved
    Part Number: DAC8718 Hi, Good day. Just want to confirm, does the NC pins of device is not internally connected to die? Connection to NC pin to ground cannot affect the device functions? Thank you in advance. Regards, Maynard

  • DAC8718: Output protection

    TI Thinks Resolved
    Part Number: DAC8718 Hi, I have used output protection circuit as per TI recommendation " https://www.ti.com/lit/ug/sbau229/sbau229.pdf " for one of my design. I want to protect output side for wrong plugging output to supply (24VDC). EX:If i…

Didn't find what you are looking for? Post a new question.