• DAC8811: Noise density specification

  

  Danilo A.

  TI Thinks Resolved

  Part Number: DAC8811 Other Parts Discussed in Thread: THS4011 Hi Team, Posting on behalf of our customer. The DAC8811 noise density specification is specified at 12nV/SqrtHz at 1 KHz. It is said that is was measured with a THS4011 as I/V converter…

  • 19 days ago
  • Data converters
  • Data converters forum
Answered

• DAC8811: DAC8811EVM - DAC8811 Transition when changing DAC

  

  Tim Page

  Resolved

  Part Number: DAC8811 Tool/software: Hello everyone, I am using a DAC8811 on a DAC8811EVM board, I could not get the USB - FTDI to do SPI correctly so am now using an Arduino for MISO, CLK & CS bit bashing the control lines. I am trying to use DAC8811…

  • Resolved

  • over 1 year ago
  • Data converters
  • Data converters forum

• DAC8801: How to use DAC8801 and DAC8811

  

  Takahashi Masahito

  TI Thinks Resolved

  Part Number: DAC8801 Is it possible to use this as a voltage-output D/A converter by connecting the IOUT pin to a buffered voltage and configuring the VREF pin as an output?

  • 1 month ago
  • Data converters
  • Data converters forum

• DAC8811: Sudden Noise in Analog Output Circuit Using DAC8811

  

  Conor

  TI Thinks Resolved

  Part Number: DAC8811 Other Parts Discussed in Thread: OPA2192 Tool/software: Hi, Currently, one of my customers is using a DAC8811I in an analog signal control circuit, and has noticed a phenomenon in which sudden noise (approximately 300nV) occurs…

  • over 1 year ago
  • Data converters
  • Data converters forum

• DAC8811: Reference Volatage

  

  Aravind TS

  Part Number: DAC8811 Tool/software: Does this DAC work on AC Reference Voltage (6 Mhz)

  • over 1 year ago
  • Data converters
  • Data converters forum
Answered

• DAC8811: The output data is incorrect

  

  ? ?

  Resolved

  Part Number: DAC8811 Other Parts Discussed in Thread: OPA2828 Tool/software: This is a test board we made based on the TI DAC8811 development board, where C2, C3, and R5 were not soldered This is the timing sequence of CLK, SDI, CS for(i=0;i<36;i…

  • Resolved

  • over 2 years ago
  • Data converters
  • Data converters forum
Answered

• DAC8811: Power-on reset

  

  Masakazu Adachi

  Resolved

  Part Number: DAC8811 Hello team, I have a question regarding to the power on reset. Could you please tell me the conditions under which this device will power-on reset? I couldn't figure it out by reading the datasheet... Regards, Masa

  • Resolved

  • over 3 years ago
  • Data converters
  • Data converters forum

• DAC8812: Errors/Inconsistencies in DAC8801/DAC8811/DAC8812 datasheets?

  

  AnBer

  TI Thinks Resolved

  Part Number: DAC8812 Other Parts Discussed in Thread: DAC8801 , DAC8811 , Team, Customer is reporting the following inconstitencies in the different datasheets. Can you please comment? 1) DAC8801: In the data sheet https://www.ti.com/lit/gpn/dac8801…

  • over 2 years ago
  • Data converters
  • Data converters forum

• DAC8811: Questions about DAC8811 power on reset circuit.

  

  Kazuya Nakai59

  Part Number: DAC8811 Hello guys. One of my customers is evaluating DAC8811 for their new products. At this moment, they have the following question. Could you please give me your reply for them? Q. What is the minimum VDD volts which the power-on…

  • over 4 years ago
  • Data converters
  • Data converters forum
Answered

• DAC8811: DAC8811 behavior without code

  

  Rohit Arora

  Resolved

  Part Number: DAC8811 Hi, I want to understand the behavior of DAC8811 if there is not SPI interface connected to IC. I have used 5Vref so it will provide 0mA or 1mA at I out pin without any code? Regards, Rohit

  • Resolved

  • over 4 years ago
  • Data converters
  • Data converters forum

Didn't find what you are looking for? Post a new question.