Search tips
Showing 91 results View by: Thread Post Sort by
    Answered

  • DLPA2000: Can I get a custom firmware builder for the DLPA2000, or can you make custom firmware for me? Also do the following functions need to be implemented?

    Resolved
    Part Number: DLPA2000 Other Parts Discussed in Thread: DLPC3433 Tool/software: I want to confirm that I DO NOT need to implement the following functions because they are not needed in my design, and I am space limited in my product Everything regarding…
    • Resolved

  • DLPC3436: We drew a board ourselves using DLPC3436+DLPA2000. How should we debug it please?

    TI Thinks Resolved
    Part Number: DLPC3436 Tool/software: We have now downloaded the firmware, how to verify the display after completing the download. And we have future demand updates. Do you have any related burning software tools and code for DLPC3436.Hope to receive…
    • Answered

  • DLPA2000: DLAP2000 buck-boost regulator

    Resolved
    Part Number: DLPA2000 Other Parts Discussed in Thread: DLPC3430 Tool/software: Hello, We have implemented a system using the DLP3430 and DLPA2000. However, we’re encountering an issue when setting the display brightness to maximum. When this happens…
    • Resolved
    • Answered

  • DLPA2000: Possible to use DLP chipset without any LEDs attached to PMIC?

    Resolved
    Part Number: DLPA2000 Other Parts Discussed in Thread: DLPC3420 , DLP160AP , DLP4710LC , DLP3010LC , DLP2010LC Tool/software: Hi, I am interested in using your DMDs for light modulation, not in a projector. As such I have no possible use for the LED driver…
    • Resolved
    • Answered

  • DLPA2000: How is the load switch used, and is it necessary to operate the DMD?

    Resolved
    Part Number: DLPA2000 Other Parts Discussed in Thread: DLP3010 Tool/software: page 24 of DLPA2000 data sheet says: "As required by the DMD data sheet, LS_OUT must stay above 1.65 V until VOFS, VRST, and VBIAS have discharged to their required safe levels…
    • Resolved
    • Answered

  • DLPA2000: What is the LED current spike on the VLED line?

    Resolved
    Part Number: DLPA2000 Other Parts Discussed in Thread: DLPC3435 , DLPC3430 , DLPC3433 , DLPC3432 , DLPC3438 Hi, When measuring power consumption, I put a current probe on the green VLED line.(LED red/blue are turned off) This is what I get: …
    • Resolved
    • Answered

  • DLPA2000: motor driver

    Resolved
    Part Number: DLPA2000 We are NOT going to use Motor Driver. How should I connect AOUT1/2 and BOUT1/2 in than case? In the Datasheet I have found info only about VINM: VINM can be left floating if the motor controller is not used
    • Resolved
    • Answered

  • DLPA2000: Standby mode

    Resolved
    Part Number: DLPA2000 Other Parts Discussed in Thread: DLP3010 , , DLPC3433 Hi expert, My device includes DLPC3433, DLPA2000 and DLP3010. We have our own board to drive DLP displays. There are 4 modes in DLP. They are OFF, Standby, Active 1 and Active…
    • Resolved
    • Answered

  • DLPA2000: Fast Park conditions

    Resolved
    Part Number: DLPA2000 Other Parts Discussed in Thread: DLPC3433 Hello, I have a custom board with the DLPA2000 and the DLPC3433. I made an initial test setting PROJ_ON high and it worked fine. I could see the splash image in the display. However, after…
    • Resolved

  • DLPA2000: PG failure

    TI Thinks Resolved
    Part Number: DLPA2000 Other Parts Discussed in Thread: DLPC3433 , DLP3010 Hello, I am trying to boot a custom board with the DLPA2000 and DLPC 3433. I have no success so far. The IRQ signal from the DLPC3433 remains high, and I note that the LS_OUT…

Didn't find what you are looking for? Post a new question.