• 

  Petr Zkrat

  • 6 days ago
  • DLP® products
  • DLP® products forum

  RE: DLPA2005: when PROJ_ON is pulled low, 1V8 on LS_OUT falls to just 0.946V

  Hi Hirak, I deeply investigated the issue and found the possible root cause. The issue was caused by PCLK being supplied when PROJ_ON was pulled low. I made a couple of HW tests: 1) Test 1: PROJ_ON low ->1V8_DLP = 0.946V 2) Test 2: PROJ_ON...
• 

  Go Bravos

  • 3 months ago
  • DLP® products
  • DLP® products forum

  DLPA2005: Power Consumption

  • Resolved

  Part Number: DLPA2005 Team, I was looking over the DLPA2005 datasheet and it seems that the input
• 

  Mayank Khandelwal

  • 2 months ago
  • DLP® products
  • DLP® products forum

  RE: DLPA2005: Output screen color error

  Shin, I have reviewed your schematic and shared my findings over private message. We can have further discussion via private messages. Thanks and regards, Mayank
• 

  Vivek Thakur

  • 2 months ago
  • DLP® products
  • DLP® products forum

  RE: DLPA2005: using DLPA2005 without driving any LEDs

  Hello Anas, It is reference design for Spectroscopy scanning application. Please use this reference design. In this application, there should not be any LED load. VLED feature is mainly for projection application where you are driving LED from DLPA2005...
• 

  Mayank Khandelwal

  • 2 months ago
  • DLP® products
  • DLP® products forum

  RE: DLPA2005: Output screen color error

  Hi Shin, Welcome to the TI E2E forum and thank you for showing interest in the DLP technology. Is your request related to schematic review? If not, can you elaborate the problem that you are facing? Regards, Mayank
• 

  Kivanc Hedili

  • 2 months ago
  • DLP® products
  • DLP® products forum

  DLPA2005: SPI communication with DLPC150

  • Resolved

  Part Number: DLPA2005 Hi, I am interested in programming DLPA2005 using its SPI port
• 

  Eriks Austrums

  • 19 days ago
  • DLP® products
  • DLP® products forum

  RE: DLPC3435: custom firmware using GUI

  Hi, >> 1. What PMIC are you using with the DLPC3435 ? We are using DLPA2005 >> 2. In what way did your attempt to change the LED brightness and splash screens fail - was there any error message, displayed improperly, etc. ? When i...
• 

  Hirak Biswas

  • 1 month ago
  • DLP® products
  • DLP® products forum

  RE: DLPC150: I can't see the DLPC150 on I2C

  Hi Rich, Could you please monitor the VCORE 1.1V from the moment of turning on the PROJ ON? Kindly check if it goes high and then low or remains low throughout. Kindly check DLPA2005 Datasheet Figure 4. Power Sequence Fault Shutdown Mode for detailed...
• 

  Øyvind2929

  • 4 months ago
  • DLP® products
  • DLP® products forum

  DLPC3478: LED_SEL timing and LED turn-on time

  TI Thinks Resolved

  Part Number: DLPC3478 I am using DLPC3478 together with DLPA2005. I am currently using internal pattern mode, though I will likely also be using the pixel-parallel streaming mode. We are not using the DLPA2005 to drive the R/G/B LEDs directly, but have...
• 

  user6015626

  • 4 months ago
  • DLP® products
  • DLP® products forum

  DLP3010EVM-LC: temperature management for LED light source

  • Resolved

  there is an ambient sensor in DLPA2005 PMIC, but I'd like to get temperature of LED light source, not PMIC.)

Didn't find what you are looking for? Post a new question.

• Ask a new question