Search tips
Showing 147 results View by: Thread Post Sort by

  • DLPC3433: Inquiries about DSI PHY Timing parameters.

    TI Thinks Resolved
    Part Number: DLPC3433 Hi, Qualcomm provides an Excel sheet for DSI timing calculation. However, it is difficult to understand how the parameters appearing there are related to the contents of the ti dlpc3433 datasheet. Please let me know what name to…
    • Answered

  • DLPC3433: EMI solution

    Resolved
    Part Number: DLPC3433 Other Parts Discussed in Thread: DLP3010 DLPC3433 TO DMD 3010 sub-LVDS signal, can a 0 ohm resistor be connected in series? It is reserved for solving EMI problems. will this affect image output quality? In order to reduce the EMI…
    • Resolved
    • Answered

  • RE: DLPC3433: PROJ_ON (ON) & host_IRQ is active. test pattern enabled. no display

    Resolved
    Nathan, I am glad to hear this is resolved. You are very welcome to the help. Please feel free to open up a new E2E thread if any new issues arise. Kind regards, Austin

  • DLPC3433: DSI Data Resistors Never Drop in

    TI Thinks Resolved
    Part Number: DLPC3433 Other Parts Discussed in Thread: DLP3010 , , DLPA2005 I have a DSI generator that I have tested with a non-TI display to produce video at timings that I want. The video data I look at with oscope that proves that it is 200mV signal…

  • DLPC3433: DSI: Signal but no Video

    Part Number: DLPC3433 I first put the MIPI master into LP11. Then I configure the DLPC3433: W 1B D7 00 //Enable DSI W 1B 10 00 00 00 00 84 03 F4 01 //Image Crop W 1B 12 00 00 00 00 84 03 F4 01 //Display Size W 1B 2E 84 03 F4 01 //External Image Size …

  • RE: DLPC3433: DSI

    Hello User, In this case a lower resolution that is supported by xrandr may need to be chosen. To do so the same steps can be used as described in the DLPC343x Setup of the DSI Setup and Debugging Guide , but with the new values in the Write: ImageCrop…

  • DLPC3433: dlpa3010

    TI Thinks Resolved
    Part Number: DLPC3433 Other Parts Discussed in Thread: DLP3010 , DLPA2000 , Hello, I just got the vertical lines on my display. Like the ones in this thread https://e2e.ti.com/support/dlp-products-group/dlp/f/dlp-products-forum/811235/dlpc3433-when-the…

  • DLPC3433: How do we get a firmware load with safe default values?

    TI Thinks Resolved
    Part Number: DLPC3433 Other Parts Discussed in Thread: DLP3010 We are trying to design a system that uses a DLPC3433CZVB, DLPA2005ERSLT, and DLP3010. In order to set the thing up, we had to download firmware from TI. There appears to be no ability to custo…

  • DLPC3433: Sending Linux Mainline driver

    Part Number: DLPC3433 Hi, Anyone interested to know or using DLPC3433 Linux driver, please let me know asap. I'm planning to send DLPC3433 driver to upstream Linux as DSI to DMD DRM bridge. I've already sent v1 before. now Planning to send fixed version…

  • RE: DLPC3433: Is PARKZ is required during power on sequence

    Jagan, The timings can be seen in Section 9.2 of the DLPC3433 Datasheet . How are VCC_18, VCC_INTF, VCC_FLASH, and PARKZ controlled in your design? From your description it sounds as though these signals are not controlled by the DLPA3005. Is this the case…

Didn't find what you are looking for? Post a new question.